<![CDATA[SoliForum - 3D Printing Community — Keenovo 120x120mm silicone heat mat under original aluminium?]]> 2016-01-27T06:44:25Z PunBB https://www.soliforum.com/topic/13522/keenovo-120x120mm-silicone-heat-mat-under-original-aluminium/ <![CDATA[Re: Keenovo 120x120mm silicone heat mat under original aluminium?]]> it dont have the 3 holes for mounting bed to plate like all SD2 use

]]> https://www.soliforum.com/user/795/ 2016-01-27T06:44:25Z https://www.soliforum.com/post/115139/#p115139 <![CDATA[Re: Keenovo 120x120mm silicone heat mat under original aluminium?]]> SSR... will look into that.

I think I will go with a silicone mat, as per this guy's recommendation, which I have found on aliexpress in the right size.

https://www.youtube.com/watch?v=eure74A9HNc

]]> https://www.soliforum.com/user/211/ 2016-01-26T17:05:30Z https://www.soliforum.com/post/115070/#p115070 <![CDATA[Re: Keenovo 120x120mm silicone heat mat under original aluminium?]]> Very convenient to get the thermistor...

Not sure if your control board can run the 6 x 6" PCB heater directly...it will probably require around 60-75 watts to run with more than that at startup.  If the board can support that current draw, then you can plug in the 6x6" and be good to go.

Now, if it turns out that your board cannot support the current draw, then you should get a SSR (Solid State Relay) DC-DC and control the bed with that; the input side of the SSR being hooked up to your control board, and the output side being used to switch the bed on and off wired directly into the Power Supply.

Also, the Power Supplies supplied by SD were notoriously under spec'd.  An upgraded PSU is recommended.

]]> https://www.soliforum.com/user/131/ 2016-01-26T16:50:17Z https://www.soliforum.com/post/115069/#p115069 <![CDATA[Re: Keenovo 120x120mm silicone heat mat under original aluminium?]]> IronMan wrote:

Try this...

http://www.makerfarm.com/index.php/heat … d-173.html


Nice one.  I hadn't found that.

Do you know whether or not I should get the integrated thermistor / heat bed relay?  I'll be looking for an install guide too

Edit:  Board is $23 and shipping is $22.50 to the UK sad

]]> https://www.soliforum.com/user/211/ 2016-01-26T15:22:49Z https://www.soliforum.com/post/115062/#p115062 <![CDATA[Re: Keenovo 120x120mm silicone heat mat under original aluminium?]]> Try this...

http://www.makerfarm.com/index.php/heat … d-173.html

]]> https://www.soliforum.com/user/131/ 2016-01-26T15:17:35Z https://www.soliforum.com/post/115061/#p115061 <![CDATA[Keenovo 120x120mm silicone heat mat under original aluminium?]]> Edit:  No help needed at this point.  Bought http://www.ebay.co.uk/itm/271826639255 and I might have questions when it gets here.  It just fits between the bolts.

New part of this post:
I think I will buy a Keenovo 150x150mm silicone heat mat and just stick it to my glass bed, mounting that on the existing aluminium bed using a spacer of some kind.

Any thoughts before I buy?  At 180W i'll be getting an SSR and have an upgraded 30A PSU.  Is that enough?


Old part of this post:
All the PCB heatbeds seem to start at 200x200mm, but I want one for my SD2.

Edit: I'm in the UK and http://3dheatbeds.com/ doesn't ship here.

Edit 2:  Mission shift time.  I want to get the 150x150mm silicone mat and milled planed aluminium sheet described in this guys video : https://www.youtube.com/watch?v=eure74A9HNc

The mat can be had on aliexpress pretty easily, but I'm not so sure
(a) what aluminium sheet to get (I want a flat one, of course)
and
(b) whether ABS/PLA will print directly onto a perfectly heated aluminium sheet
(c) how to stick the mat to the sheet.

]]> https://www.soliforum.com/user/211/ 2016-01-26T15:01:00Z https://www.soliforum.com/post/115060/#p115060