<![CDATA[SoliForum - 3D Printing Community — e3d lite6 ptfe shift]]> 2016-02-01T03:49:28Z PunBB https://www.soliforum.com/topic/13450/e3d-lite6-ptfe-shift/ <![CDATA[Re: e3d lite6 ptfe shift]]> That'll be 20 bucks, cash only, no receipt big_smile

]]> https://www.soliforum.com/user/4188/ 2016-02-01T03:49:28Z https://www.soliforum.com/post/115467/#p115467 <![CDATA[Re: e3d lite6 ptfe shift]]> Thanks!

]]> https://www.soliforum.com/user/9121/ 2016-02-01T03:47:06Z https://www.soliforum.com/post/115466/#p115466 <![CDATA[Re: e3d lite6 ptfe shift]]> 290 is just fine. Between 295-300 is where you risk damaging the thermistor just from tem,p fluctuations during initial heating

]]> https://www.soliforum.com/user/4188/ 2016-02-01T03:33:39Z https://www.soliforum.com/post/115465/#p115465 <![CDATA[Re: e3d lite6 ptfe shift]]> From my current config.h file:

// When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection.
#define HEATER_0_MAXTEMP 270
#define HEATER_1_MAXTEMP 245
#define HEATER_2_MAXTEMP 245
#define BED_MAXTEMP 200

What should I set the max temp to with the v6cano with its stock thermistor? 290/295?

]]> https://www.soliforum.com/user/9121/ 2016-02-01T03:27:34Z https://www.soliforum.com/post/115464/#p115464 <![CDATA[Re: e3d lite6 ptfe shift]]> Received! Excited about all the new things I can print with a v6!

]]> https://www.soliforum.com/user/9121/ 2016-01-26T17:35:36Z https://www.soliforum.com/post/115073/#p115073 <![CDATA[Re: e3d lite6 ptfe shift]]> Great! I ordered new PTFE and everything to make a v6 volcano(except the fan) from Filastruder last night. Plan on using that in my new 3d printer, when I buy or build one, and continue using the lite6 on my i3, since I've got orders pilling up. Thanks for all the help!

]]> https://www.soliforum.com/user/9121/ 2016-01-22T15:50:09Z https://www.soliforum.com/post/114791/#p114791 <![CDATA[Re: e3d lite6 ptfe shift]]> That's likely some leakage from plastic you've been printing with, not the PTFE itself.

No need for an auto tune as the thermal properties of the hotend are unchanged.

]]> https://www.soliforum.com/user/221/ 2016-01-22T15:08:49Z https://www.soliforum.com/post/114789/#p114789 <![CDATA[Re: e3d lite6 ptfe shift]]> Last night I had time to pull everything apart, and tonight I can clean the PLA out of the heatsink. Everything went smooth, the only concern I have is when I pulled the PTFE out, it has black residue on it. After a very close inspection, I heed the warnings about PTFE very seriously, I could see that it wasn't melted and the inside of the tube wasn't damaged or discolored, only the outside from where it butts up against the nozzle up about 3-4mm. I can post a picture when I get home. I highest temp I ever run is some ABS at 235C and have only ever taken the hotend to 245C twice, to put on and take off the nozzle. Should I be running an autotune when I get the new PTFE?

]]> https://www.soliforum.com/user/9121/ 2016-01-22T14:44:01Z https://www.soliforum.com/post/114786/#p114786 <![CDATA[Re: e3d lite6 ptfe shift]]> Yes, the Lite6 heatsink with Volcano is a go. That's the setup I've been running on the Solidoodle I have.

]]> https://www.soliforum.com/user/221/ 2016-01-20T21:35:33Z https://www.soliforum.com/post/114640/#p114640 <![CDATA[Re: e3d lite6 ptfe shift]]> I believe it will, although haven't done this myself.

]]> https://www.soliforum.com/user/2291/ 2016-01-20T20:58:52Z https://www.soliforum.com/post/114631/#p114631 <![CDATA[Re: e3d lite6 ptfe shift]]> But the lite6 heatsink will still work with the volcano right? That's what I read from elmoret's comment above. Please let me know if I'm wrong, and thanks for all the help!

]]> https://www.soliforum.com/user/9121/ 2016-01-20T20:42:32Z https://www.soliforum.com/post/114630/#p114630 <![CDATA[Re: e3d lite6 ptfe shift]]> The heatsinks are different between the v6 and Lite6
The volcano and V6 use the same heatsink and heatbreak but the nozzles are different lengths.

]]> https://www.soliforum.com/user/2291/ 2016-01-20T20:21:12Z https://www.soliforum.com/post/114624/#p114624 <![CDATA[Re: e3d lite6 ptfe shift]]> The heatsink is the same for the v6 and the lite6, correct? If I get a volcano starter pack would I need to purchase the v6 heatbreak also, or is that for using the higher temps the v6 is capable of?

]]> https://www.soliforum.com/user/9121/ 2016-01-20T19:57:03Z https://www.soliforum.com/post/114620/#p114620 <![CDATA[Re: e3d lite6 ptfe shift]]> Top notch help!

]]> https://www.soliforum.com/user/9121/ 2016-01-20T17:26:36Z https://www.soliforum.com/post/114613/#p114613 <![CDATA[Re: e3d lite6 ptfe shift]]> The collet has a lip at the top and that lip should have about a 1 mm gap between it and the hotend.  The force of the tube pushing into the hotend and the teeth on collet grabbing the tube push the collet up into a narrow portion (at top) of the hotend.  This is what squeezes the collet teeth into the tube and therefore preventing movement of the tube.  Some cut a small U-shaped shim out of a credit card and slide that between the metal of the hot end and the upper lip of the collet.  This forces the collet to remain in a position that allow those teeth to grab.

]]> https://www.soliforum.com/user/2291/ 2016-01-20T16:45:01Z https://www.soliforum.com/post/114609/#p114609