<![CDATA[SoliForum - 3D Printing Community — Repetier problems on 1.0a]]> 2016-04-09T07:25:37Z PunBB https://www.soliforum.com/topic/13393/repetier-problems-on-10a/ <![CDATA[Re: Repetier problems on 1.0a]]> you have 1.0A this behaviour happen when you use 1.0 FW. 0.91 is not for 1.0A, only 0.92 support it
I see you can revert back to stock FW, it means you use 1.0 FW and not 1.0A FW
It means also you use wrong setting in configuration in repetier
Be sure you set MODEL 1 in repetier (change / save / close / reopen to verify change is done) before flashing

]]> https://www.soliforum.com/user/8495/ 2016-04-09T07:25:37Z https://www.soliforum.com/post/120822/#p120822 <![CDATA[Re: Repetier problems on 1.0a]]> Just installed repetier 0.91 on my davinci 1.0a  with win 10 could not install 0.92  Anyway after install can not move z axis up.  Have tried setting home position to max, -200 200 inverting the z axis.  Seems to me i'm on the limit switch and it is inverted. 
Did anyone else have this problem after making the switch.  Ya I did not think to home all axis BEFORE SHORTING J37  even reverting to the stock firmware has the same problem.
If I knew which connectors were for the limit switches I would switch them but short of tearing down the whole machine...
Can somebody help.

]]> https://www.soliforum.com/user/8767/ 2016-04-09T05:31:33Z https://www.soliforum.com/post/120818/#p120818 <![CDATA[Re: Repetier problems on 1.0a]]> using bossac with stock FW on AiO  / 1.0A/ 2.0A make printer unusable because FW is encrypted for these printers

Contact support or flash repetier

]]> https://www.soliforum.com/user/8495/ 2016-04-06T20:50:23Z https://www.soliforum.com/post/120639/#p120639 <![CDATA[Re: Repetier problems on 1.0a]]> Hello everybody,

Please, please help me:

I have a DA VINCI 1.0 AIO, I tried to make a firmware downgrade from 1.2 to 1.1.3 by bossac, my printer still not working.
How can I solve this isuue.

Thanks in advance.

]]> https://www.soliforum.com/user/14163/ 2016-04-06T19:06:24Z https://www.soliforum.com/post/120633/#p120633 <![CDATA[Re: Repetier problems on 1.0a]]> milojaimes007 wrote:

I just flashed my xyz da Vinci 1.0 AiO and I'm trying to print PLA
I seem to have got jammed and extruder feed wheels jammed I cleared jam and cleaned wheels but now I can't get wheels to turn again

I love repetier so far much better firmware and first hack too super excited and feeling a bit lost

Start a new thread, you'll be more likely to get an answer. I can try to help you through PM if you want.

]]> https://www.soliforum.com/user/13278/ 2016-03-02T15:26:01Z https://www.soliforum.com/post/118483/#p118483 <![CDATA[Re: Repetier problems on 1.0a]]> I just flashed my xyz da Vinci 1.0 AiO and I'm trying to print PLA
I seem to have got jammed and extruder feed wheels jammed I cleared jam and cleaned wheels but now I can't get wheels to turn again

I love repetier so far much better firmware and first hack too super excited and feeling a bit lost

]]> https://www.soliforum.com/user/13838/ 2016-03-02T02:25:45Z https://www.soliforum.com/post/118465/#p118465 <![CDATA[Re: Repetier problems on 1.0a]]> snu wrote:

I just slapped Repetier on my Da Vinci 1.0a 3F10A (somehow) and it works nicely. I've already gotten all the axes and the extruder to work, as well as playing Imperial March, but my prints keep sticking to the extruder. No matter what I try (sheet of paper calibration, slow speeds on the first layer), nothing works. Any help is appreciated.

Glad to hear that repetier is working on the new 1.0A model. I also am right on the fence of flashing mine. Was just concerned about reading online that it was not working properly with the 1.0A 3F10A.
Which version did you use? Thanks Dave

]]> https://www.soliforum.com/user/13761/ 2016-02-24T16:31:07Z https://www.soliforum.com/post/117743/#p117743 <![CDATA[Re: Repetier problems on 1.0a]]> Morgan wrote:

I have problem after installing repetier firmware
I experience too much material comes out during print
Any nody has solutions for me?


Have you done all your basic calibration? Like extruder steps per mm?

]]> https://www.soliforum.com/user/7731/ 2016-01-21T08:16:40Z https://www.soliforum.com/post/114685/#p114685 <![CDATA[Re: Repetier problems on 1.0a]]> I have problem after installing repetier firmware
I experience too much material comes out during print
Any nody has solutions for me?

]]> https://www.soliforum.com/user/13375/ 2016-01-21T08:09:12Z https://www.soliforum.com/post/114684/#p114684 <![CDATA[Re: Repetier problems on 1.0a]]> That seems to have worked. I was so used to not having to use glue with the XYZ firmware that I forgot about it. Printing perfectly now!

]]> https://www.soliforum.com/user/13278/ 2016-01-13T19:24:38Z https://www.soliforum.com/post/114058/#p114058 <![CDATA[Re: Repetier problems on 1.0a]]> snu wrote:

I just slapped Repetier on my Da Vinci 1.0a 3F10A (somehow) and it works nicely. I've already gotten all the axes and the extruder to work, as well as playing Imperial March, but my prints keep sticking to the extruder. No matter what I try (sheet of paper calibration, slow speeds on the first layer), nothing works. Any help is appreciated.


So you mean they are not sticking to the bed then? Try a light coat of aquanet hairspray on the bed, or Elmers purple glue stick on the bed..

]]> https://www.soliforum.com/user/7731/ 2016-01-13T18:46:30Z https://www.soliforum.com/post/114051/#p114051 <![CDATA[Repetier problems on 1.0a]]> I just slapped Repetier on my Da Vinci 1.0a 3F10A (somehow) and it works nicely. I've already gotten all the axes and the extruder to work, as well as playing Imperial March, but my prints keep sticking to the extruder. No matter what I try (sheet of paper calibration, slow speeds on the first layer), nothing works. Any help is appreciated.

]]> https://www.soliforum.com/user/13278/ 2016-01-13T18:22:32Z https://www.soliforum.com/post/114048/#p114048