SoliForum - 3D Printing Community — Lasers not working, Usb not written to...

Re: Lasers not working, Usb not written to...

2016-01-20T16:16:38Z

No problem. Let me know if you need additional help.

- Uriah

Re: Lasers not working, Usb not written to...

2016-01-20T13:22:53Z

Thank you hairu, elmoret and C_D for your help...
now to get this calibrated and scanning...

Re: Lasers not working, Usb not written to...

2016-01-19T02:49:58Z

You already have the latest version of the software. I am glad you were finally able to connect.

Re: Lasers not working, Usb not written to...

2016-01-19T00:38:40Z

Used my new wifi adapter..
got a new sadder message...
now it was not even detecting my wifi...when the wifi net JACKY is obviously connected...

so I went back to the original dongle..
and connected to a new hdmi screen which was better suited to using the raspian software.
Went back and foth in the settings and having read something about some upping their memory to 192 i did the same... tried my wifi over and over but it simply did not hold on to the password although it always detected my network.. did this about 6 times more out of frustration than with any hope that it would work, and suddently it connected...
it just did...it accepted the same password to the same network it had refused previously.. so perhaps something to do with the memory? or just coincidence.

So I turned it off.. and turned it on and it connected again. Did it 4 times and it connected perfectly.
So I tried an un centered, un calibrated, un everything scan... just to see if it would do it...

Probably a new myriad of questions will follow...
tried to click on the upsate file (assume frelss will turn into atlas3d software or something) inserted my serial number, saved and got no update available... is that normal or should my software have somehow been updated?

Re: Lasers not working, Usb not written to...

2016-01-17T22:50:47Z

Actually, you can copy/paste the text displayed when you click "Show Details" on the config page.

Re: Lasers not working, Usb not written to...

2016-01-17T22:43:00Z

Raspberry Pi has a lower amount of power that it can deliver to USB than a standard PC can. Looking in your screenshots above it appears that you have at least a keyboard and another device connected to the USB. Please disconnect everything except for the flash drive and WiFi adapter and see if your results are the same. If so, please run the following command from a command line and paste the last 50 or so lines here.

dmesg

- Uriah

Re: Lasers not working, Usb not written to...

2016-01-15T02:51:02Z

Awesome will try it tomorrow
It says something about the self powered hub... is there a particular hub that i should connect to?
Thanks
Beto

Re: Lasers not working, Usb not written to...

2016-01-15T00:25:27Z

The below post is a little old, but it suggest that your WiFi dongle should be just fine on the Raspberry Pi.

https://www.raspberrypi.org/forums/view … mp;t=13733

- Uriah

Re: Lasers not working, Usb not written to...

2016-01-14T18:33:07Z

Hello
I can borrow this to test the wifi.. however I believe the wifi is correctly working since the wifi dongle does in fact detect the diffrent providers.. JACKY at home , betored as my hotspot, Moldex1 as my work wifi...
anyway can you check to see if the sd card i burned has the required driver for this..

Also if the energy/voltage requirements match those of the pi
Thanks again

Re: Lasers not working, Usb not written to...

2016-01-14T12:22:22Z

Betorango,

Would you like us to send you a new WiFi adapter to see if there is a hardware issue? Do you have another one that you can try?

Regards,
Uriah

Re: Lasers not working, Usb not written to...

2016-01-12T02:59:49Z

Re-googled how to open a wifi hotspot and was found i has skipped a step...was able to leave hotspot open..

redid everything exactly as before...
turned on,inserted usb, lasers turned on 5 secs removed usb, connected to win10
selected open network, tried to save.. but A password must be entered sign appeared.. put in a space and it accepted it..
(the second time around I erased it in the notepad view of atlas3d_cfg file where it appeared)
loaded usb into atlas 3d, lasers turned on for 5 secs or so, removed usb.. got the original murobo screen.. no red letters... but no connect button either...

Re: Lasers not working, Usb not written to...

2016-01-12T02:17:15Z

Was unable to remove the pasword from my hotspot...

Turned on the adtlas3
Inserted the wifi dongle(also tried the exact procedure with the wifi dongle preinserted)
inserted usb
lasers turned on, turned off 5 secs or so later
removed usb
inserted into my win10 laptop (also into my winxplaptop and win8 desktop)
beto-red-note (my hotspot was one fo the options available, also tried it for my home wifi)
chose it
updated password, saved, ejected usb correctly
just for laughs turned on my laptop, erased the wifi... reconected using same password...
reinserted usb into 3d
lasers turn on for about 30 secs then turn off
remove usb put it in win10/winxp/win8 computers
get...

bang head on desk...
repeat...

Re: Lasers not working, Usb not written to...

2016-01-11T23:39:29Z

Betoarango,

Let me know if you are still unable to connect. We will do everything we can to get you up and running.

Uriah

Re: Lasers not working, Usb not written to...

2016-01-11T20:01:34Z

just googled it and my cellphone does have the option to allow my hotspot to connect to any device (I assume without password).. I will test it as soon as I get home.

You have no idea how over my head I am on this....

Also just became a member... as opposed to newbie...

Re: Lasers not working, Usb not written to...

2016-01-11T19:58:22Z

elmoret wrote:

Can you post your /etc/supplicant.conf file here?
would that be this?

If not just tell me how and I will try it..
Can you connect to your network if you disable security (the password)?
Dont think I can disable password... however I tried it in 3 different sites (home, hotspot, work) where I know the password..
I made sure of this because I disconnected my cell phone and reconected it using the same password. i will see if my cell phone hotspot can work wothout a password. If so I will try it...
Also I tried it using all 3 methods.. however the wifi adapter must be working in some measure since the Murobo setup program (using the usb) does in fact give me JACKY as one of the network suggestions to connect to...

thanks for the continued help.