<![CDATA[SoliForum - 3D Printing Community — Installed an E3D Hotend and PT100 Thermocouple cant go above 312C]]> 2015-12-03T17:36:01Z PunBB https://www.soliforum.com/topic/13000/installed-an-e3d-hotend-and-pt100-thermocouple-cant-go-above-312c/ <![CDATA[Re: Installed an E3D Hotend and PT100 Thermocouple cant go above 312C]]> Solution here http://www.soliforum.com/topic/13005/so … rmocouple/

]]> https://www.soliforum.com/user/956/ 2015-12-03T17:36:01Z https://www.soliforum.com/post/110848/#p110848 <![CDATA[Re: Installed an E3D Hotend and PT100 Thermocouple cant go above 312C]]> elmoret wrote:

What color are your heater wires?

Also PEEK is quite difficult to print, requires a 200C heated bed and ideally a 150C heated enclosure.

I've seen this post on 3 different message boards. Spreading out the discussion makes it hard to have consolidated answers for a search.

I will be updating each one with my solution, the 40W heater element and the walkthough to do the upgrade.  Since there isnt a ton of information on the upgrade I wanted to write a walkthrough so no one has to do what I did.

Thanks for the help elmoret!

]]> https://www.soliforum.com/user/956/ 2015-12-03T15:59:43Z https://www.soliforum.com/post/110827/#p110827 <![CDATA[Re: Installed an E3D Hotend and PT100 Thermocouple cant go above 312C]]> What color are your heater wires?

Also PEEK is quite difficult to print, requires a 200C heated bed and ideally a 150C heated enclosure.

I've seen this post on 3 different message boards. Spreading out the discussion makes it hard to have consolidated answers for a search.

]]> https://www.soliforum.com/user/221/ 2015-12-02T23:11:50Z https://www.soliforum.com/post/110776/#p110776 <![CDATA[Re: Installed an E3D Hotend and PT100 Thermocouple cant go above 312C]]> if he doesn't chime in soon you might send him a PM or forum mail

]]> https://www.soliforum.com/user/2291/ 2015-12-02T21:07:00Z https://www.soliforum.com/post/110769/#p110769 <![CDATA[Re: Installed an E3D Hotend and PT100 Thermocouple cant go above 312C]]> Printing PEEK.  Mainly just evaluating different blends of PEEK for 3D printing, like will it even come out of the nozzle evaluations.  Thanks!

]]> https://www.soliforum.com/user/956/ 2015-12-02T21:02:57Z https://www.soliforum.com/post/110768/#p110768 <![CDATA[Re: Installed an E3D Hotend and PT100 Thermocouple cant go above 312C]]> What are you planning on using that requires 400C?
elmoret will have to help out with this question.

]]> https://www.soliforum.com/user/2291/ 2015-12-02T21:02:03Z https://www.soliforum.com/post/110767/#p110767 <![CDATA[Installed an E3D Hotend and PT100 Thermocouple cant go above 312C]]> Hello all, I have a Solidoodle 3 with the PrintrBoard Mobo.  I upgraded the hot end to an E3D v6.  I upgraded the powersupply to the recommended 360w PS from Amazon.  I installed a PT100 thermocouple with the e3d interfacing kit.  I flashed it with the firmware.

Everything works great under 310C but the temp seems to just taper off and plateau at 311C.

Any ideas on how i can get it to output at 400C?

Thanks

]]> https://www.soliforum.com/user/956/ 2015-12-02T20:43:17Z https://www.soliforum.com/post/110763/#p110763