<![CDATA[SoliForum - 3D Printing Community — M105]]> 2017-09-23T05:44:19Z PunBB https://www.soliforum.com/topic/12733/m105/ <![CDATA[Re: M105]]> Landin81 wrote:

Installed repetier on my da vinci 1.0A.
using simplify3d.

I finaly had some nice prints, but suddenly when connecting to the machine it start to send m105 code and nothing happens, no temperature showing in s3d =/

Anyone know what the problem can be?

Attempting connection at \\.\COM26...
  Connected to machine!
SENT: T0
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105

I had this exact same problem.  To solve it I went to this website:

https://support.microsoft.com/en-us/hel … b-problems

Apparently there was a problem with the USB port and my laser printer?!?!   Once that was fixed, I was able to immediately connect to my Davinci 1.0 (Repetier 0.92, Simplify3D).

]]> https://www.soliforum.com/user/9702/ 2017-09-23T05:44:19Z https://www.soliforum.com/post/138405/#p138405 <![CDATA[Re: M105]]> Solved..

There was a conflict between some serial protocols.

After reinstalling windows everything works as it should smile

]]> https://www.soliforum.com/user/11562/ 2015-11-06T22:14:50Z https://www.soliforum.com/post/109071/#p109071 <![CDATA[Re: M105]]> carl_m1968 wrote:
Landin81 wrote:

Ok..

So, I found the problem, everytime I shut off the printer, or if the S3d have been connected to the printer and I close the program. I need to reinstall the arduini due drivers to the printer to get it to work again.. I dont know what to do about this =/


I bet you are running Windows 10..?

No im running windows 7 -64bit.

Also I installed everything on one of my other computer, and it connected fine, over and over again. =/

So now the problem is down to my computer =/

]]> https://www.soliforum.com/user/11562/ 2015-11-06T15:33:30Z https://www.soliforum.com/post/109048/#p109048 <![CDATA[Re: M105]]> Landin81 wrote:

Ok..

So, I found the problem, everytime I shut off the printer, or if the S3d have been connected to the printer and I close the program. I need to reinstall the arduini due drivers to the printer to get it to work again.. I dont know what to do about this =/


I bet you are running Windows 10..?

]]> https://www.soliforum.com/user/7731/ 2015-11-06T04:39:45Z https://www.soliforum.com/post/109019/#p109019 <![CDATA[Re: M105]]> Ok..

So, I found the problem, everytime I shut off the printer, or if the S3d have been connected to the printer and I close the program. I need to reinstall the arduini due drivers to the printer to get it to work again.. I dont know what to do about this =/

]]> https://www.soliforum.com/user/11562/ 2015-11-06T04:36:09Z https://www.soliforum.com/post/109018/#p109018 <![CDATA[Re: M105]]> Once you install Repetier you can no longer disconnect or turn off the computer. It prints now using a live stream. The only other choice would be to put the SDcard on an extension cable then you could print from the SDcard.

]]> https://www.soliforum.com/user/7731/ 2015-11-05T17:40:37Z https://www.soliforum.com/post/108951/#p108951 <![CDATA[Re: M105]]> Im not sure why, and now I have change the port to one in the back and now it says com29 insted.

Its connected, I can move all axsis from s3d.

This is how it looks in my tree:
http://soliforum.com/i/?Wm7mRJA.png


Hmm. When I go in to change the port, it says that the ports are used =/

I know that this has something to do with the printer =/

http://soliforum.com/i/?iewtndA.png


EDIT: So now I have clear the regeditkey and the printer is now at port5. But still only M105 with no respons..


EDIT: Reinstalled the USB to serial driver and changed to a new cable, seems to work, getting codes back from printer.
BUT: If having the box on both bed and extruder for the "wait for temperature controller to stabilize before build" checked, only the bed will heat.

And now I unchecked the box for the bed and extruder starts to heat up. But when heated up, the printer restarted itself..=/

And when trying to reconnect, I get the M105 without any respons again. GHHAAAAAAAA

EDIT: Everytime this happens, I can delete the Arduino DUE driver and reinstall it, than it works, for now. I have to do some prints and see if its F***ing up again.

Isnt there a way to upload the build to the printer, so that my computer dont need to stay connected to the printer during the build?

]]> https://www.soliforum.com/user/11562/ 2015-11-05T14:09:25Z https://www.soliforum.com/post/108936/#p108936 <![CDATA[Re: M105]]> For one why are you on COM 26? Some programs have issues with COM ports higher than 5. Not sure why but I remember reading this on a printer related post.

Is COM 26 even the correct port? I trust you already tried the usual of unplugging all the USB and rebooting the computer and printer. Also make sure you are using a direct connection and not a hub. If the hub is powered it might be OK but using hubs with 3D printers is not advised.

]]> https://www.soliforum.com/user/7731/ 2015-11-05T07:43:38Z https://www.soliforum.com/post/108928/#p108928 <![CDATA[M105]]> Installed repetier on my da vinci 1.0A.
using simplify3d.

I finaly had some nice prints, but suddenly when connecting to the machine it start to send m105 code and nothing happens, no temperature showing in s3d =/

Anyone know what the problem can be?

Attempting connection at \\.\COM26...
  Connected to machine!
SENT: T0
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105

]]> https://www.soliforum.com/user/11562/ 2015-11-05T07:27:52Z https://www.soliforum.com/post/108927/#p108927