<![CDATA[SoliForum - 3D Printing Community — XYZ 1.0A Belt Break]]> 2015-10-29T13:12:55Z PunBB https://www.soliforum.com/topic/12638/xyz-10a-belt-break/ <![CDATA[Re: XYZ 1.0A Belt Break]]> carl_m1968 wrote:
barry1685 wrote:

I believe its a 20 tooth gear with 3mm to 6mm width (you need to measure the other y belt width) doesn't matter what length it is, you can cut the new belt


If you cut it, how do you rejoin it into the small 3 inch loop needed to link the motor gear to the rear y drive gear?

As for measuring just a piece of string in place of the belt. Loop around and mark where joins then remove, tape at joint and measure.

Yikes, didn't know it was THAT belt. you can't rejoin that belt.

]]> https://www.soliforum.com/user/8171/ 2015-10-29T13:12:55Z https://www.soliforum.com/post/108502/#p108502 <![CDATA[Re: XYZ 1.0A Belt Break]]> No,on crash. All components factory installed. I will lean toward belt quality.

]]> https://www.soliforum.com/user/12404/ 2015-10-29T02:15:04Z https://www.soliforum.com/post/108487/#p108487 <![CDATA[Re: XYZ 1.0A Belt Break]]> Could be too tight, pulleys misaligned, or could have just been a cheap belt.

]]> https://www.soliforum.com/user/7731/ 2015-10-29T01:04:14Z https://www.soliforum.com/post/108478/#p108478 <![CDATA[Re: XYZ 1.0A Belt Break]]> no idea. Are you crashing the carriage?

]]> https://www.soliforum.com/user/10955/ 2015-10-29T01:03:14Z https://www.soliforum.com/post/108477/#p108477 <![CDATA[Re: XYZ 1.0A Belt Break]]> Thanks Mark for the help. Any ideas of what would cause premature failure of belt?

]]> https://www.soliforum.com/user/12404/ 2015-10-28T21:53:27Z https://www.soliforum.com/post/108460/#p108460 <![CDATA[Re: XYZ 1.0A Belt Break]]> the number on the belt is 132-S2M
you can prolly get it here
http://www.kpaulindustrial.com/100-s2m-132.html

]]> https://www.soliforum.com/user/10955/ 2015-10-28T02:46:28Z https://www.soliforum.com/post/108416/#p108416 <![CDATA[Re: XYZ 1.0A Belt Break]]> If you would supply me with belt size that would be very much appreciated. My plan is to outsource replacement belt  myself. XYZ customer support is rather slow. Thanks again.

]]> https://www.soliforum.com/user/12404/ 2015-10-27T22:53:16Z https://www.soliforum.com/post/108397/#p108397 <![CDATA[Re: XYZ 1.0A Belt Break]]> carriage belts you can fix to the carriage so it doesn't have to closed loop as the fixing it to the carriage closes the loop and you don't ever drag your carriage through the gears or idler. The y transfer belt you need to buy as the correct sized loop belt ,as it will loop through multiple times so any thing you used to close the loop will have to go through the gears and any idlers.

I can look at my small y drive belt and give you the number once mine is done printing.

]]> https://www.soliforum.com/user/10955/ 2015-10-27T22:14:24Z https://www.soliforum.com/post/108392/#p108392 <![CDATA[Re: XYZ 1.0A Belt Break]]> barry1685 wrote:

I believe its a 20 tooth gear with 3mm to 6mm width (you need to measure the other y belt width) doesn't matter what length it is, you can cut the new belt


If you cut it, how do you rejoin it into the small 3 inch loop needed to link the motor gear to the rear y drive gear?

As for measuring just a piece of string in place of the belt. Loop around and mark where joins then remove, tape at joint and measure.

]]> https://www.soliforum.com/user/7731/ 2015-10-27T16:47:12Z https://www.soliforum.com/post/108366/#p108366 <![CDATA[Re: XYZ 1.0A Belt Break]]> barry1685 wrote:

I believe its a 20 tooth gear with 3mm to 6mm width (you need to measure the other y belt width) doesn't matter what length it is, you can cut the new belt


If you cut it, how do you rejoin it into the small 3 inch loop needed to link the motor gear to the rear y drive gear?

]]> https://www.soliforum.com/user/7731/ 2015-10-27T16:44:30Z https://www.soliforum.com/post/108365/#p108365 <![CDATA[Re: XYZ 1.0A Belt Break]]> I believe its a 20 tooth gear with 3mm to 6mm width (you need to measure the other y belt width) doesn't matter what length it is, you can cut the new belt

]]> https://www.soliforum.com/user/8171/ 2015-10-27T13:37:54Z https://www.soliforum.com/post/108353/#p108353 <![CDATA[Re: XYZ 1.0A Belt Break]]> Not that I am attacking the OP, I am not. I am just curious how people break or even wear belts. I had a printer for a while that ran daily for 5 years and never broke or belt or even showed any wear on them. Could be be over tightening them or am I missing something here?

]]> https://www.soliforum.com/user/7731/ 2015-10-26T17:19:59Z https://www.soliforum.com/post/108314/#p108314 <![CDATA[Re: XYZ 1.0A Belt Break]]> It is the small belt "Y" axis. Unfortunately, I trashed the belt ,therefore I cannot verify belt size. If you have belt size available, could you please forward to me? XYZ stated it will be 2-3 days before they could get back to me on replacement. Thanks for the help.

]]> https://www.soliforum.com/user/12404/ 2015-10-26T16:47:53Z https://www.soliforum.com/post/108310/#p108310 <![CDATA[Re: XYZ 1.0A Belt Break]]> Which belt broke? gt2 belts work great for y axis's but x axis will need some sort of clip

]]> https://www.soliforum.com/user/8171/ 2015-10-26T14:45:32Z https://www.soliforum.com/post/108305/#p108305 <![CDATA[Re: XYZ 1.0A Belt Break]]> well there are a few things you can do.
you can order a t2 timing belt just get the number off the broken belt.

if you do it right you can even make one for the x or y carriages  by buying t2 timing belt and then fastening the loose ends to the carriages.

]]> https://www.soliforum.com/user/10955/ 2015-10-26T02:22:45Z https://www.soliforum.com/post/108291/#p108291