<![CDATA[SoliForum - 3D Printing Community — Hello Im new to 3D printing]]> 2016-01-03T21:25:37Z PunBB https://www.soliforum.com/topic/12540/hello-im-new-to-3d-printing/ <![CDATA[Re: Hello Im new to 3D printing]]> Try the 16, I don't have the answer.  On mine I only have the Sanguino option.
It won't hurt to try the others.  Also make sure in the configuration.h you have the correct board number selected.

]]> https://www.soliforum.com/user/2291/ 2016-01-03T21:25:37Z https://www.soliforum.com/post/113176/#p113176 <![CDATA[Re: Hello Im new to 3D printing]]> The board uses an ATMEGA1284P chip, on selection in arduino do i select 16Mhz or 8Mhz. been searching these setup information, can't find this answer. Tnx

I chose 8Mhz, verify/compile got error compiling.

Done editing boards.txthttp://soliforum.com/i/?p6Z1CRU.png

]]> https://www.soliforum.com/user/12293/ 2016-01-03T12:12:40Z https://www.soliforum.com/post/113144/#p113144 <![CDATA[Re: Hello Im new to 3D printing]]> yes i will correct the installation and get back here, tnx for the advices.

]]> https://www.soliforum.com/user/12293/ 2016-01-03T06:39:37Z https://www.soliforum.com/post/113135/#p113135 <![CDATA[Re: Hello Im new to 3D printing]]> If it's a Sangunololu board you need to get those files into the hardware folder of Arduino.  You can pull them from Arduino 022 or just use version 022.  Then you will select Sanguino from that drop down menu.
Hope that helps.

]]> https://www.soliforum.com/user/2291/ 2016-01-03T06:11:04Z https://www.soliforum.com/post/113133/#p113133 <![CDATA[Re: Hello Im new to 3D printing]]> i have been checking the installation, i think im not on marlin? and my arduino board is sanguinololu, arduino has uno selected. pls confirm.http://soliforum.com/i/?ZrMQQcy.jpghttp://soliforum.com/i/?Et1N6lU.jpghttp://soliforum.com/i/?he0KqI2.png

im still learning, i think i have to correct this install...

]]> https://www.soliforum.com/user/12293/ 2016-01-03T05:49:18Z https://www.soliforum.com/post/113132/#p113132 <![CDATA[Re: Hello Im new to 3D printing]]> Get us a screenshot of the hotend section in configuration.h.  Something isn't right with that heat chart and until you get the temp line smooth and stable, you won't get the quality.

]]> https://www.soliforum.com/user/2291/ 2016-01-02T15:56:06Z https://www.soliforum.com/post/113098/#p113098 <![CDATA[Re: Hello Im new to 3D printing]]> here is a current print, I'm working on the casing footers

]]> https://www.soliforum.com/user/12293/ 2016-01-02T06:24:56Z https://www.soliforum.com/post/113085/#p113085 <![CDATA[Re: Hello Im new to 3D printing]]> Yes I was also expecting E3D, but the guy who sold me this unit came and installed this hotend. That is why I came here to seek help, that guy just builds and sells stuff and Im trying to learn on my own without his support. Hoping that this printer wont be a waste of money and my time. I was already getting low hopes but I'll make this printer work.

Was already planning to resell it but how when it doesnt work at all, its been about 6 months since I bought it.  Right now its given me good prints and the only thing I need to resolve it the fluctuating temperature. Not sure if its harware or firmware issues, re-installed repetier twice, repaired the clogging, the fan holder replaced.



elmoret wrote:

Just an FYI - you said you're getting an E3D, that is definitely not an E3D hotend.

]]> https://www.soliforum.com/user/12293/ 2016-01-02T06:20:32Z https://www.soliforum.com/post/113084/#p113084 <![CDATA[Re: Hello Im new to 3D printing]]> Just an FYI - you said you're getting an E3D, that is definitely not an E3D hotend.

]]> https://www.soliforum.com/user/221/ 2016-01-02T06:12:09Z https://www.soliforum.com/post/113083/#p113083 <![CDATA[Re: Hello Im new to 3D printing]]> its same, not printing here

PID
P: 30
I: 2.62
D: 75

]]> https://www.soliforum.com/user/12293/ 2016-01-02T06:04:54Z https://www.soliforum.com/post/113082/#p113082 <![CDATA[Re: Hello Im new to 3D printing]]> Bang bang is exactly what it sounds like.  It is on off instead of PWM control.
Can you post that while the printer is not in motion?  The bed output looks more like bang bang than the curves seen in your extruder.  Bang bang is adequate for a bed but not precise enough for the extruder.

]]> https://www.soliforum.com/user/2291/ 2016-01-01T18:49:45Z https://www.soliforum.com/post/113047/#p113047 <![CDATA[Re: Hello Im new to 3D printing]]> its printing, whats a Bang Bang?

]]> https://www.soliforum.com/user/12293/ 2016-01-01T18:16:44Z https://www.soliforum.com/post/113043/#p113043 <![CDATA[Re: Hello Im new to 3D printing]]> A screenshot of the output enabled will help.  If that was done with no movement, it suggests you may have Bang Bang enabled in the firmware.  You should expect a nice flat line.

]]> https://www.soliforum.com/user/2291/ 2016-01-01T18:06:06Z https://www.soliforum.com/post/113041/#p113041 <![CDATA[Re: Hello Im new to 3D printing]]> extrusion is better now but im getting fluctuations in bed & extruder temp, done PID.

]]> https://www.soliforum.com/user/12293/ 2016-01-01T17:33:40Z https://www.soliforum.com/post/113037/#p113037 <![CDATA[Re: Hello Im new to 3D printing]]> will calibrate tnx wardjr

]]> https://www.soliforum.com/user/12293/ 2015-12-30T01:46:46Z https://www.soliforum.com/post/112896/#p112896