<![CDATA[SoliForum - 3D Printing Community — Some trick to recover connection with Repetier after manual leveling?]]> 2015-09-28T17:49:49Z PunBB https://www.soliforum.com/topic/12409/some-trick-to-recover-connection-with-repetier-after-manual-leveling/ <![CDATA[Re: Some trick to recover connection with Repetier after manual leveling?]]> mozzieblue wrote:

What I do is, after turning off the printer, disconnet repetier, then turn on the printer and reconnect. Sometimes you might have close and open repetier.

I'm quite sure I've tried all the combinations, but I'll try your suggestion. Thanks.

]]> https://www.soliforum.com/user/12134/ 2015-09-28T17:49:49Z https://www.soliforum.com/post/106410/#p106410 <![CDATA[Re: Some trick to recover connection with Repetier after manual leveling?]]> Antonious wrote:
kev0175 wrote:

Well I'm not using repetier but when I want to reconnect with Simplify3D I just unplug the USB wait for the disconnect sound and plug back in, I don't know if this will help.

If the printer has been off, I'm quite sure that unplugging and pluging the usb cable doesn't run in my case because I did it. The error message received says something like "denied connection from COM4" (if COM4 is the open port with the printer).

Thanks.


What I do is, after turning off the printer, disconnet repetier, then turn on the printer and reconnect. Sometimes you might have close and open repetier.

]]> https://www.soliforum.com/user/12019/ 2015-09-28T17:38:36Z https://www.soliforum.com/post/106409/#p106409 <![CDATA[Re: Some trick to recover connection with Repetier after manual leveling?]]> kev0175 wrote:

Well I'm not using repetier but when I want to reconnect with Simplify3D I just unplug the USB wait for the disconnect sound and plug back in, I don't know if this will help.

If the printer has been off, I'm quite sure that unplugging and pluging the usb cable doesn't run in my case because I did it. The error message received says something like "denied connection from COM4" (if COM4 is the open port with the printer).

Thanks.

]]> https://www.soliforum.com/user/12134/ 2015-09-28T16:45:55Z https://www.soliforum.com/post/106401/#p106401 <![CDATA[Re: Some trick to recover connection with Repetier after manual leveling?]]> Well I'm not using repetier but when I want to reconnect with Simplify3D I just unplug the USB wait for the disconnect sound and plug back in, I don't know if this will help.

]]> https://www.soliforum.com/user/9677/ 2015-09-28T16:40:29Z https://www.soliforum.com/post/106400/#p106400 <![CDATA[Re: Some trick to recover connection with Repetier after manual leveling?]]> evanalmighty wrote:

That method is only necessary on the stock XYZ firmware.  Why don't you just use the manual bed leveling feature in the menu now that you have Repetier firmware installed?  You should really go through the entire menu and see what options are available to you.

Yes, I tried the manual leveling on the Repetier firmware, but... it isn't so simple and quick to that explained by carl. In the Repetier protocol you have to check more tnan 3 points and tweak sometimes two screws to adjust only one point. I appreciate your suggestion, of course.

]]> https://www.soliforum.com/user/12134/ 2015-09-28T16:25:47Z https://www.soliforum.com/post/106396/#p106396 <![CDATA[Re: Some trick to recover connection with Repetier after manual leveling?]]> That method is only necessary on the stock XYZ firmware.  Why don't you just use the manual bed leveling feature in the menu now that you have Repetier firmware installed?  You should really go through the entire menu and see what options are available to you.

]]> https://www.soliforum.com/user/8801/ 2015-09-28T15:25:54Z https://www.soliforum.com/post/106388/#p106388 <![CDATA[Some trick to recover connection with Repetier after manual leveling?]]> To do a manual leveling according to the easy method by carl sticked in this forum I have to start a print and then off the printer.

As when you order a test print from the display panel of Da Vinci with Repetier firm (not Repetier-host) the heating doesn't occur and so the leveling is not valid, I need to use the computer and to order a print from Repetier-host. Ok, I do it and when printing is initiating I stop it by putting off the printer (interrupting its energy) or by an emergency stop from Repetier. In both cases the only way I find to reconnect the printer to the Repetier-host is by restarting the computer (first putting on the printer and then the restart).

Is there some way to reconnect to Repetier-host avoiding the uncomfortable restarting?

]]> https://www.soliforum.com/user/12134/ 2015-09-28T10:53:58Z https://www.soliforum.com/post/106375/#p106375