<![CDATA[SoliForum - 3D Printing Community — repetier issue]]> 2015-09-13T16:49:18Z PunBB https://www.soliforum.com/topic/12278/repetier-issue/ <![CDATA[Re: repetier issue]]> And you were right, just for the noise part, it worth the upgrade.... it also look like it unleashed Simplify 3D too...

]]> https://www.soliforum.com/user/11781/ 2015-09-13T16:49:18Z https://www.soliforum.com/post/105346/#p105346 <![CDATA[Re: repetier issue]]> I know!, it's just before I set to table 5, I was able to get the PETG to stick, now with table 5 active the initial temp seems right but I need to figure out the correct temp for this filament...

]]> https://www.soliforum.com/user/11781/ 2015-09-13T16:17:06Z https://www.soliforum.com/post/105343/#p105343 <![CDATA[Re: repetier issue]]> You need to use glue stick or hairspray on the bed. The system will not home at the start of a print unless you add the command to do so to your start gcode.

]]> https://www.soliforum.com/user/7731/ 2015-09-13T02:22:20Z https://www.soliforum.com/post/105319/#p105319 <![CDATA[Re: repetier issue]]> now the frikkin stuff won't stick to the bed...

]]> https://www.soliforum.com/user/11781/ 2015-09-13T02:07:04Z https://www.soliforum.com/post/105318/#p105318 <![CDATA[Re: repetier issue]]> ok i think i got it... now need to learn how the bitch behave... is it normal behavior that you have to home all before each print? I'm using S3D and usually at start the bed is down and work from there... now if I start a print with the bed down, the print will start but the bed will stay down...

]]> https://www.soliforum.com/user/11781/ 2015-09-13T01:14:01Z https://www.soliforum.com/post/105315/#p105315 <![CDATA[Re: repetier issue]]> Arduino: 1.5.8 (Windows 8), Board: "Arduino Due (Native USB Port)"

Sketch uses 158,156 bytes (30%) of program storage space. Maximum is 524,288 bytes.

processing.app.debug.RunnerException: Couldn't find a Board on the selected port. Check that you have the correct port selected.  If it is correct, try pressing the board's reset button after initiating the upload.

    at cc.arduino.packages.uploaders.SerialUploader.waitForUploadPort(SerialUploader.java:199)

    at cc.arduino.packages.uploaders.SerialUploader.uploadUsingPreferences(SerialUploader.java:95)

    at processing.app.Sketch.upload(Sketch.java:1713)

    at processing.app.Sketch.exportApplet(Sketch.java:1624)

    at processing.app.Sketch.exportApplet(Sketch.java:1596)

    at processing.app.Editor$DefaultExportHandler.run(Editor.java:2392)

    at java.lang.Thread.run(Unknown Source)

Couldn't find a Board on the selected port. Check that you have the correct port selected.  If it is correct, try pressing the board's reset button after initiating the upload.

  This report would have more information with
  "Show verbose output during compilation"
  enabled in File > Preferences.

]]> https://www.soliforum.com/user/11781/ 2015-09-13T00:29:53Z https://www.soliforum.com/post/105309/#p105309 <![CDATA[Re: repetier issue]]> when I try this, it give me an error concerning the com port...

]]> https://www.soliforum.com/user/11781/ 2015-09-13T00:22:09Z https://www.soliforum.com/post/105305/#p105305 <![CDATA[Re: repetier issue]]> icebob wrote:

so I will need to short j37 again right?

No, once the firmware is installed the machine is seen differently. All you need to do is make sure no programs are open using the machine. Then open the folder  for your firmware and double click the file Repetier.INO. It should open in Arduino. Make your changes and then upload. That is all there is to it. That jumper shorting was a one time thing to erase the stock firmware which makes the machine be seen in a different way from Repetier. Stock firmware used a different communication setup.

]]> https://www.soliforum.com/user/7731/ 2015-09-13T00:20:31Z https://www.soliforum.com/post/105304/#p105304 <![CDATA[Re: repetier issue]]> so I will need to short j37 again right?

]]> https://www.soliforum.com/user/11781/ 2015-09-13T00:12:33Z https://www.soliforum.com/post/105303/#p105303 <![CDATA[Re: repetier issue]]> icebob wrote:

ok is there a way just to set it back to 5 without reflashing the whole thing?

Nope, you have to flash. Once it has been done once it is as easy as turning the machine on.

]]> https://www.soliforum.com/user/7731/ 2015-09-13T00:01:48Z https://www.soliforum.com/post/105302/#p105302 <![CDATA[Re: repetier issue]]> ok is there a way just to set it back to 5 without reflashing the whole thing?

]]> https://www.soliforum.com/user/11781/ 2015-09-12T23:49:38Z https://www.soliforum.com/post/105301/#p105301 <![CDATA[Re: repetier issue]]> It should still be 5 to my knowledge. The issue is the Da Vinci has a resistor on the main board that changes the value of the thermistor. However both the stock and E3D hotends use the same standard 100K thermistor.

]]> https://www.soliforum.com/user/7731/ 2015-09-12T23:47:06Z https://www.soliforum.com/post/105300/#p105300 <![CDATA[Re: repetier issue]]> not stock extruder E3D V6

]]> https://www.soliforum.com/user/11781/ 2015-09-12T23:39:00Z https://www.soliforum.com/post/105299/#p105299 <![CDATA[Re: repetier issue]]> It should be 5 with a stock extruder.

]]> https://www.soliforum.com/user/7731/ 2015-09-12T23:31:40Z https://www.soliforum.com/post/105298/#p105298 <![CDATA[Re: repetier issue]]> I put the 8 in config.h before flashing... i think default was 5...

]]> https://www.soliforum.com/user/11781/ 2015-09-12T22:58:39Z https://www.soliforum.com/post/105295/#p105295