<![CDATA[SoliForum - 3D Printing Community — Solidoodle 2 heater problems]]> 2015-06-27T04:21:38Z PunBB https://www.soliforum.com/topic/11603/solidoodle-2-heater-problems/ <![CDATA[Re: Solidoodle 2 heater problems]]> I've read a similar case where the power supply was at fault for causing sudden temp shutdowns.

]]> https://www.soliforum.com/user/11275/ 2015-06-27T04:21:38Z https://www.soliforum.com/post/100030/#p100030 <![CDATA[Re: Solidoodle 2 heater problems]]> MAX/MINTEMP, faulty thermistor wiring.

]]> https://www.soliforum.com/user/221/ 2015-06-26T22:58:11Z https://www.soliforum.com/post/100013/#p100013 <![CDATA[Re: Solidoodle 2 heater problems]]> carl_m1968 wrote:

Could you have the temps in your slicer set to zero? Normally you preheat using the manual buttons in your host. Once heated you start the print. At that point slicer settings will override manual settings. If higher it will raise them and wait till they are reached before printing. If lower it again will wait till it cools. In your case the temps could be set to zero in slicer. Only thing that makes sense since both machines do it.

Setting temps to zero in slic3r just tells slic3r not to worry about/adjust the temps, mine is set to zero for both 1st layer and other layers and I have no problems maintaining temps that are set manually.

There is something else going on...

]]> https://www.soliforum.com/user/10399/ 2015-06-26T13:04:56Z https://www.soliforum.com/post/99975/#p99975 <![CDATA[Re: Solidoodle 2 heater problems]]> Not set to zero in slic3r.  I can get most of the way through a job.  And its random when it does it.

]]> https://www.soliforum.com/user/5254/ 2015-06-26T04:43:39Z https://www.soliforum.com/post/99958/#p99958 <![CDATA[Re: Solidoodle 2 heater problems]]> Sorry.only one machine.....accidentally put an s.

]]> https://www.soliforum.com/user/5254/ 2015-06-26T04:42:21Z https://www.soliforum.com/post/99957/#p99957 <![CDATA[Re: Solidoodle 2 heater problems]]> Could you have the temps in your slicer set to zero? Normally you preheat using the manual buttons in your host. Once heated you start the print. At that point slicer settings will override manual settings. If higher it will raise them and wait till they are reached before printing. If lower it again will wait till it cools. In your case the temps could be set to zero in slicer. Only thing that makes sense since both machines do it.

]]> https://www.soliforum.com/user/7731/ 2015-06-26T01:31:14Z https://www.soliforum.com/post/99945/#p99945 <![CDATA[Re: Solidoodle 2 heater problems]]> Yes....it looks like I just turned them off but the buttons still show on.

]]> https://www.soliforum.com/user/5254/ 2015-06-26T01:23:32Z https://www.soliforum.com/post/99944/#p99944 <![CDATA[Re: Solidoodle 2 heater problems]]> Does repetier-host show the actual temp as it goes down?

]]> https://www.soliforum.com/user/2752/ 2015-06-25T20:21:29Z https://www.soliforum.com/post/99916/#p99916 <![CDATA[Solidoodle 2 heater problems]]> My printers will randomly start cooling both the heated bed and the extruder until they reach room temperature.   Anyone know why.  Its weird that both do it despite the heater buttons still showing on.  Both show 0 volts at the board.....once they shut off.   I had the printer at 210c for the extruder and 100c for the bed.

Thanks,
Zach

]]> https://www.soliforum.com/user/5254/ 2015-06-25T06:00:23Z https://www.soliforum.com/post/99868/#p99868