<![CDATA[SoliForum - 3D Printing Community — Pololu AVR Progammer]]> 2015-06-26T06:22:38Z PunBB https://www.soliforum.com/topic/11499/pololu-avr-progammer/ <![CDATA[Re: Pololu AVR Progammer]]> Yes, I did it with Arduino on the Mac.

]]> https://www.soliforum.com/user/9900/ 2015-06-26T06:22:38Z https://www.soliforum.com/post/99964/#p99964 <![CDATA[Re: Pololu AVR Progammer]]> THanks, did you get it working using Arduino software on the Mac, I found the jumper but couldn't get it to work, tried flip and arduino.

]]> https://www.soliforum.com/user/7070/ 2015-06-19T21:24:07Z https://www.soliforum.com/post/99463/#p99463 <![CDATA[Re: Pololu AVR Progammer]]> I used Arduino on mine. Worked like a charm.

Take a look at the picture in this thread: http://www.soliforum.com/topic/11338/ca … hat-i-try/

BUT the connector on the motherboard needs to be turned around 180 degrees from how it is in that picture!!!

]]> https://www.soliforum.com/user/9900/ 2015-06-18T12:41:11Z https://www.soliforum.com/post/99304/#p99304 <![CDATA[Re: Pololu AVR Progammer]]> i just used avr dude on ubutu, you should be able to do it on windows, check pages 9 through 11 on the e3d sticky

]]> https://www.soliforum.com/user/9321/ 2015-06-17T16:32:05Z https://www.soliforum.com/post/99194/#p99194 <![CDATA[Re: Pololu AVR Progammer]]> Crucial wrote:

i can upload a picture of how to do it tomorrow if youd like, i need to reflash it anyway

is the avr programer the only way of updating the press firmware?  then i need to buy it also.
what kind of software needed? arduino?

]]> https://www.soliforum.com/user/6911/ 2015-06-16T11:25:44Z https://www.soliforum.com/post/99052/#p99052 <![CDATA[Re: Pololu AVR Progammer]]> i can upload a picture of how to do it tomorrow if youd like, i need to reflash it anyway

]]> https://www.soliforum.com/user/9321/ 2015-06-16T01:55:11Z https://www.soliforum.com/post/99025/#p99025 <![CDATA[Re: Pololu AVR Progammer]]> the two pins next to the usb port is for the jumper, basically short those two together when you plug the usb cord in. the connector goes like thishttp://s39.photobucket.com/user/zerrb/media/20150305_211444_zpsp6odscs1.jpg.html but flip it so the ribbon cable goes to the right.

]]> https://www.soliforum.com/user/9321/ 2015-06-16T01:54:35Z https://www.soliforum.com/post/99024/#p99024 <![CDATA[Pololu AVR Progammer]]> I am trying to reflash the firmware on my press, so I purchased this http://www.amazon.co.uk/Pololu-POL1300- … 84-21/url]

The programmer comes with a 6 pin plug and the jumper on the board only has 2 pins, please could someone let me know how this works?  Do i need to purchase an additional cable/adapter to make it work/fit?

Many Thanks

]]> https://www.soliforum.com/user/7070/ 2015-06-15T20:06:21Z https://www.soliforum.com/post/98989/#p98989