<![CDATA[SoliForum - 3D Printing Community — Heated Bed Peeling Away]]> 2015-04-24T22:27:08Z PunBB https://www.soliforum.com/topic/10897/heated-bed-peeling-away/ <![CDATA[Re: Heated Bed Peeling Away]]> Yeah check those wires on the heating pad. Mine was completely fried, so I had to buy a mk2b heatbed from Amazon.

]]> https://www.soliforum.com/user/9974/ 2015-04-24T22:27:08Z https://www.soliforum.com/post/94093/#p94093 <![CDATA[Re: Heated Bed Peeling Away]]> Acetone shouldn't hurt a silicone pad.

]]> https://www.soliforum.com/user/2291/ 2015-04-24T22:24:51Z https://www.soliforum.com/post/94092/#p94092 <![CDATA[Re: Heated Bed Peeling Away]]> The replacement pad SD sent me had 3M 467MP adhesive tape on it. <$5 on ebay will get you more than enough of that tape for two beds. I used acetone to soften the bits of old adhesive on the bed, and to prep the bed for the new pad.

[EDIT] I didn't use acetone on the pad, since I had a new pad. No idea if it's safe for the pad.

]]> https://www.soliforum.com/user/7353/ 2015-04-24T22:18:34Z https://www.soliforum.com/post/94091/#p94091 <![CDATA[Re: Heated Bed Peeling Away]]> Keep me posted!

]]> https://www.soliforum.com/user/10573/ 2015-04-24T20:26:35Z https://www.soliforum.com/post/94077/#p94077 <![CDATA[Re: Heated Bed Peeling Away]]> Yep no problem!

]]> https://www.soliforum.com/user/10573/ 2015-04-24T20:25:29Z https://www.soliforum.com/post/94076/#p94076 <![CDATA[Re: Heated Bed Peeling Away]]> Yes, it's the stock Press heater for now at least. The wires are fine, so I'll give the adhesive spray a try and see what happens. Thanks!

]]> https://www.soliforum.com/user/9900/ 2015-04-24T17:16:55Z https://www.soliforum.com/post/94038/#p94038 <![CDATA[Re: Heated Bed Peeling Away]]> Do you have the stock press model heater?

]]> https://www.soliforum.com/user/10573/ 2015-04-24T17:15:31Z https://www.soliforum.com/post/94037/#p94037 <![CDATA[Re: Heated Bed Peeling Away]]> Yeah, that is true. But if you check the wires on your heating pad and try the adhesive spray u think you would get some good results!

]]> https://www.soliforum.com/user/10573/ 2015-04-24T15:06:27Z https://www.soliforum.com/post/94014/#p94014 <![CDATA[Re: Heated Bed Peeling Away]]> Not sure about that at 100 degrees...

]]> https://www.soliforum.com/user/9900/ 2015-04-24T14:36:10Z https://www.soliforum.com/post/94003/#p94003 <![CDATA[Re: Heated Bed Peeling Away]]> You could try spray adhesive and see if that works!

]]> https://www.soliforum.com/user/10573/ 2015-04-24T13:08:15Z https://www.soliforum.com/post/93993/#p93993 <![CDATA[Heated Bed Peeling Away]]> And on to my next problem... It's just one thing after another!

OK so I can no longer get my heated bed up to 100 degrees. Weirdly though, when I touch it, it actually feels hotter than it used to. So I had a look under the bed, and the pas is peeling away from the aluminium. There is a triangular area about 3 inches on each side which has come unstuck. That's presumably only going to get bigger.

So what's the best method for re-sticking it?

]]> https://www.soliforum.com/user/9900/ 2015-04-24T11:04:26Z https://www.soliforum.com/post/93979/#p93979