SoliForum - 3D Printing Community — Gidday from a Kiwi

Re: Gidday from a Kiwi

2015-04-10T23:06:24Z

madfalcon81

A copy of the bottle I drew up along with the stl files is going to put into 3D Modelling/Scanning/Design

Would appreciate your comments

Dave

Re: Gidday from a Kiwi

2015-04-10T18:06:12Z

Tin Falcon - Thanks for the video, have subscribed to his channel now so I can go through his videos for tips and tricks.

There is a box sitting in my living room which I ampining to open but the house is up for sale and I am not going to unpack it until I know I am going to be settled. Only good thing is I can spent the time to find any pitfalls. But I WANT to play with my toy NOW !!!!

madfalcon81 - Had a play at work yesterday and it goes to gether as detailed in the article. Will fiddle around today and hopefully be able to post the drawing and STL files later today or tomorrow.
One thing I did note though is that it is easiest to layout the thread arrangement as a section to help confirm pitch and tooth shape before producing a helix. that way you can ensure correct mesh of the thread. Also I found that it was easiest to oversize the thread length then make a couple of cubes and subtract the thread back to it's required length before unioning the thread to a revolved body. Hope this helps

Dave

Re: Gidday from a Kiwi

2015-04-09T22:39:10Z

Check out the videos on you tube by Chuck Hellebuyck on the davinci lots of good info.
here is a sample

This guy really seems to know how to get the most from thr DaVinci.

tin

Re: Gidday from a Kiwi

2015-04-09T21:02:40Z

Thanks, I look into it

Re: Gidday from a Kiwi

2015-04-09T17:47:23Z

In answer to your question have a look at this tutorial on producing a threaded screw

http://www.ellenfinkelstein.com/acadblo … aded-bolt/

It has been a while since I have done a threaded cap in AutoCAD normally model things like this in inventor but will have a play over the weekend to confirm it all works as shown but do not see any flaws or fish hooks as shown in the tutorial

Another post that may be of help when trying to do a worm gear thread is

http://www.cadtutor.net/forum/postimages/gear1.pdf

Hope this helps and will confirm the screw thread tutorial after I've had a play

Re: Gidday from a Kiwi

2015-04-09T10:58:14Z

Here is a question: I tried to build in Autocad a "bottle" for my firm rubber stamp. It consist of 2 sides wich screw one into another (like a bottle and its cap) but those 2 sides are equal. For the top side I have to extrude a helix from the cilinder, but it says helix is a surface and no solid (of course I do a little triangle wich is sweeped around the helix). Please take in mind I am begginer and selfeducated in Autocad. Thanks !

Gidday from a Kiwi

2015-04-09T04:22:55Z

Did a silly thing the other day and bought a new Da Vinci 3D printer. (Was going so cheap I couldn't stop myself from offering the toy a new home)

Well it's turned up so thought it might be an idea to find out how to make it work proper like so did a bit of form reading and think it's to throw off the lurker's cloak.

A bit about myself, I am draughtsman with just over 30 years in the profession and nearly 20 of those in production design where a 3D printer would have been helpful. Instead I used to have to make models from card and tape

Now working in Building Services hence the printer is now classified as a toy

Have an extensive knowledge of AutoCAD, MEP, Revit and Inventor so if anyone is using them and wants a pointer or two I'll see what I can do

Cheers

Dave