<![CDATA[SoliForum - 3D Printing Community — Solidoodle 2 seems to be resetting]]> 2015-03-19T00:19:24Z PunBB https://www.soliforum.com/topic/10414/solidoodle-2-seems-to-be-resetting/ <![CDATA[Re: Solidoodle 2 seems to be resetting]]> Nothing in the com logs from what I can see just stops.
It is on the desktop.
I had to use ABS Juice and some blue painter tape to get some ABS to print on my printerbot.

]]> https://www.soliforum.com/user/10007/ 2015-03-19T00:19:24Z https://www.soliforum.com/post/90090/#p90090 <![CDATA[Re: Solidoodle 2 seems to be resetting]]> Ok - something else worth checking is your power options if you have a laptop.  Change the power to never go to sleep as long as it is plugged in.  If you're using a desktop don't worry about this and keep looking for loose connectors.

Is there anything in the com log after it stops?

]]> https://www.soliforum.com/user/6087/ 2015-03-16T01:50:40Z https://www.soliforum.com/post/89800/#p89800 <![CDATA[Re: Solidoodle 2 seems to be resetting]]> that is the strange thing. I wiggled it around to see if it would reset and nothing. I shook the entire printer back and forth nothing.
I flip it over again it works again.
I start a print on it everything going great..then it just stop dead mid print still..

]]> https://www.soliforum.com/user/10007/ 2015-03-16T01:02:53Z https://www.soliforum.com/post/89795/#p89795 <![CDATA[Re: Solidoodle 2 seems to be resetting]]> Its good to hear that you may have successfully reflashed your board! (We'll know for sure later)  Your description does make it sound like a loose connector now.  I would probably start with the USB connector on the board since it is famous for becoming loose.  Try to hold the cable near the board in different directions and see if that helps.  When laying on the side, the cable may have tension in a different direction than when it is upright.

]]> https://www.soliforum.com/user/6087/ 2015-03-16T00:42:10Z https://www.soliforum.com/post/89793/#p89793 <![CDATA[Re: Solidoodle 2 seems to be resetting]]> Well I did an verify again and noticed the verify stops at the same point byte number it gives me an error.
it does say done uploading.
but i am now noticing it resets every time I shift the printer so something have to be loose or something.
but only when it is right side up, when i have it on its side it doesn't

]]> https://www.soliforum.com/user/10007/ 2015-03-16T00:25:34Z https://www.soliforum.com/post/89792/#p89792 <![CDATA[Re: Solidoodle 2 seems to be resetting]]> I've gotten that error before it wasn't the absence of a Bootloader I just don't remember what the issue was.  I do know this sometimes a warning is just that, a warning.  I have flashed with errors before and had no issues.  I would guess you have something incorrect in the configuration.h so don't get discouraged.

]]> https://www.soliforum.com/user/2291/ 2015-03-16T00:07:52Z https://www.soliforum.com/post/89790/#p89790 <![CDATA[Re: Solidoodle 2 seems to be resetting]]> See if this looks like your situation:
http://reprap.org/wiki/Sanguinololu#Software

]]> https://www.soliforum.com/user/6087/ 2015-03-15T23:36:06Z https://www.soliforum.com/post/89787/#p89787 <![CDATA[Re: Solidoodle 2 seems to be resetting]]> That's the same board I had before I got the rumba - it's a 644.  I can't remember exactly why at the moment but I gave up on flashing it for some reason or another.  I think it had something to do with the chip lacking a bootloader from the factory and me not wanting to mess with an AVR programmer at the time.

]]> https://www.soliforum.com/user/6087/ 2015-03-15T23:15:56Z https://www.soliforum.com/post/89784/#p89784 <![CDATA[Re: Solidoodle 2 seems to be resetting]]> Do you have the correct board chosen?

]]> https://www.soliforum.com/user/2291/ 2015-03-15T22:59:04Z https://www.soliforum.com/post/89781/#p89781 <![CDATA[Re: Solidoodle 2 seems to be resetting]]> I am getting Stk500_getSync(): not in sync:resp=0x89 error.
then I tried again and got a resp=0xd7
and then I got something about core not being able to be renamed.

]]> https://www.soliforum.com/user/10007/ 2015-03-15T22:16:23Z https://www.soliforum.com/post/89776/#p89776 <![CDATA[Re: Solidoodle 2 seems to be resetting]]> So select in configuration.h file SD2 or 3(4) and then choose what board you have from the list.
For a stock setup that's all you need to do.  Then click save then verify.  If no errors it's good to flash.  Just hit the reset on the board and click upload.  It will tell you when it's done.
If your issue was firmware related then this should fix it.  If not your back to connection issues.

]]> https://www.soliforum.com/user/2291/ 2015-03-15T21:44:35Z https://www.soliforum.com/post/89774/#p89774 <![CDATA[Re: Solidoodle 2 seems to be resetting]]> ok I'm there.

]]> https://www.soliforum.com/user/10007/ 2015-03-15T20:38:44Z https://www.soliforum.com/post/89768/#p89768 <![CDATA[Re: Solidoodle 2 seems to be resetting]]> Download the firmware and navigate via file - new in Arduino and find the file Marlin.ino file and open it.  Once there you'll have tabs across the top you want the configuration.h tab.
Once there let us know.

]]> https://www.soliforum.com/user/2291/ 2015-03-15T20:27:08Z https://www.soliforum.com/post/89763/#p89763 <![CDATA[Re: Solidoodle 2 seems to be resetting]]> ok. I have no idea where to go from here.
I downloaded the prepared version 1.05 started it up.
Went to board selected the mega664
selected my com3.
Then found it is in examples marlin.
and compiling now.

and now avrdude not in sync resp0xd7

]]> https://www.soliforum.com/user/10007/ 2015-03-15T20:06:14Z https://www.soliforum.com/post/89758/#p89758 <![CDATA[Re: Solidoodle 2 seems to be resetting]]> thank you. I will post my results.

]]> https://www.soliforum.com/user/10007/ 2015-03-15T19:01:13Z https://www.soliforum.com/post/89747/#p89747