<![CDATA[SoliForum - 3D Printing Community — Need help with print Quality]]> 2015-03-15T02:27:00Z PunBB https://www.soliforum.com/topic/10388/need-help-with-print-quality/ <![CDATA[Re: Need help with print Quality]]> It could also be under/over extrusion, some extra filament is hanging of the sides so that could be the problem.  Also be sure there are no clogs and the hotend is clean. big_smile

]]> https://www.soliforum.com/user/8348/ 2015-03-15T02:27:00Z https://www.soliforum.com/post/89683/#p89683 <![CDATA[Re: Need help with print Quality]]> Try running these speeds mate these seem to work a dream for me?

]]> https://www.soliforum.com/user/9465/ 2015-03-14T12:59:30Z https://www.soliforum.com/post/89627/#p89627 <![CDATA[Re: Need help with print Quality]]> Can you post your GCODE?

]]> https://www.soliforum.com/user/9113/ 2015-03-14T12:43:57Z https://www.soliforum.com/post/89626/#p89626 <![CDATA[Re: Need help with print Quality]]> Thanks guys, see speed settings attached. It's the same cartridge I've used for multiple prints so far, mostly simple things sliced by the XYZ Program which all printed fine. Guessing it's something to do with Slic3r and maybe the XYZ Software transmitting the files incorrectly?
Might try downgrading the firmware, my printer is new and running 1.0.1 (?).

]]> https://www.soliforum.com/user/9895/ 2015-03-14T04:50:03Z https://www.soliforum.com/post/89609/#p89609 <![CDATA[Re: Need help with print Quality]]> I had this issue too. I still have no idea what caused it but downgrading my firmware from .J to .G fixed it

]]> https://www.soliforum.com/user/7512/ 2015-03-13T21:42:17Z https://www.soliforum.com/post/89545/#p89545 <![CDATA[Re: Need help with print Quality]]> What are your speeds in Slic3r???

]]> https://www.soliforum.com/user/9465/ 2015-03-13T14:59:07Z https://www.soliforum.com/post/89482/#p89482 <![CDATA[Re: Need help with print Quality]]> Is this new filament or have you used it in the past? Meaning this same roll. Did work well then?

]]> https://www.soliforum.com/user/7731/ 2015-03-13T02:54:26Z https://www.soliforum.com/post/89444/#p89444 <![CDATA[Need help with print Quality]]> Hey Guys

Got a small problem with print quality and not sure what could be the problem.
I've had my DaVinci 1.0 For about a month now, using Slic3r for the gcode and XYZ Software to print.
Belt tension is good and I have hot glue gunned the loose brass bushings on both Z and Y Axis, print bed is solid and calibrated too.
The item I am printing has been created in 123D Design and printed before successfully with the XYZ Software.

Brief Scli3r Settings from memory (Will post screenshots later when home).

Layer height is 0.1mm
Bed temp 100, then 95 after 1st layers.
Extruder temp is 230 then 225
Extrusion Multiplier is 0.90 (Works well for my other prints).
Print speeds are low, 30 or lower.

STL File has been passed through STL Repair (netfabb) as well.
Any help is much appreciated.

Images attached.

Thanks,

]]> https://www.soliforum.com/user/9895/ 2015-03-13T01:14:02Z https://www.soliforum.com/post/89431/#p89431