SoliForum - 3D Printing Community — Max temp help

Re: Max temp help

2015-02-28T16:59:30Z

ok i tried that firmware and so far so good been printing for 3hrs now and hasnt stooped once, thanks very much! As far as the motors not moving after homing it i believe thats a RH bug as it dont do it in the older version.

Re: Max temp help

2015-02-28T04:00:26Z

Yup SD4, ok thanks will try it in the morning

Re: Max temp help

2015-02-28T03:01:32Z

Use this
https://github.com/ozadr1an/Solidoodle- … in_v1_beta

Re: Max temp help

2015-02-28T02:40:29Z

which printer do you have? I have the SD4 - havent done any firmware updates.

Re: Max temp help

2015-02-28T02:39:01Z

could i use the firmware form here? https://github.com/mlaws/solidoodle2-marlin

Re: Max temp help

2015-02-28T02:23:11Z

ok just checked mine and its fine, its only been doing it since i updated the firmware, i got my firmware file from Solidoodle is there a better place?

Re: Max temp help

2015-02-27T23:20:04Z

madkow007 wrote:

i am also also using RH 1.0.6 and have the same issue of having to bump the X & Y endstops after homing all axis before they can be moved - not really sure what is up with that...
i think it may have something to do with the odd behavior i get if i try to add the ending G code to home X & Y after a job is completed, too...

um,yup...

i dont have any problems with it stopping mid-print tho...

are your stepper motors overheating maybe?

most likely the X axis motor - mine used to get really hot - too hot to touch. I found a fan mount in the forums here somewhere, printed that out and put a fan on that motor and it hasnt overheated since. best thing I have done to this printer so far... aside from adjusting the trimpots that were way over spec...

Re: Max temp help

2015-02-27T22:11:21Z

are you using the same version of RH, right now i am trying to fix the bigger problem of it stopping mid print

Re: Max temp help

2015-02-27T21:09:33Z

i am also also using RH 1.0.6 and have the same issue of having to bump the X & Y endstops after homing all axis before they can be moved - not really sure what is up with that...
i think it may have something to do with the odd behavior i get if i try to add the ending G code to home X & Y after a job is completed, too...

Re: Max temp help

2015-02-27T03:38:38Z

Also after it stops you can push the extruder around, as the motors aren't "locked". Could it be that the power supply isnt big enough and caint handle the extra fan and bigger heater?

Re: Max temp help

2015-02-27T02:50:55Z

ok i fixed that but still stops and says "mk" and i press the "OK" button and it keeps printing then after a little it repeats

Re: Max temp help

2015-02-27T00:08:58Z

Just bump up the baud rate in RH. the board can handle 250000 just fine.

Re: Max temp help

2015-02-26T23:29:19Z

i went back and looked at my firmware and the baud rate was 250000 but in RH i have it set to 115200 as Solidoodle support says, should it be like that in the firmware?

Re: Max temp help

2015-02-26T23:19:26Z

i should also add it does it multiable times a print

Re: Max temp help

2015-02-26T23:06:28Z

Hey i keep having it stop a some random point in the print and on the log is says "mk" and i have to send "ok" then it keeps printing, it only does it on some files, any idea?