<![CDATA[SoliForum - 3D Printing Community — Slic3r giving me hell AGAIN]]> 2015-02-20T01:42:24Z PunBB https://www.soliforum.com/topic/10084/slic3r-giving-me-hell-again/ <![CDATA[Re: Slic3r giving me hell AGAIN]]> OneMoreCast wrote:
wardjr wrote:
jagowilson wrote:

Your retraction is too slow, I'm guessing, because 1mm is more than enough. Try 70mm/s

And you are slightly over extruding.



Again!?!?!? Aghhhh, i thank you guys a billion times for your patience...always juggling settings

I think you are either squishing the walls of the cube too much or your calipers are poorly calibrated/sloppy. From my experience with a .4 on an e3dv6, your extrusion multiplier should be lower if e steps is properly set.

]]> https://www.soliforum.com/user/7321/ 2015-02-20T01:42:24Z https://www.soliforum.com/post/86292/#p86292 <![CDATA[Re: Slic3r giving me hell AGAIN]]> That's what Hero's do wink

]]> https://www.soliforum.com/user/2291/ 2015-02-20T01:11:27Z https://www.soliforum.com/post/86288/#p86288 <![CDATA[Re: Slic3r giving me hell AGAIN]]> wardjr wrote:
jagowilson wrote:

Your retraction is too slow, I'm guessing, because 1mm is more than enough. Try 70mm/s

And you are slightly over extruding.



Again!?!?!? Aghhhh, i thank you guys a billion times for your patience...always juggling settings

]]> https://www.soliforum.com/user/8772/ 2015-02-20T01:07:16Z https://www.soliforum.com/post/86285/#p86285 <![CDATA[Re: Slic3r giving me hell AGAIN]]> jagowilson wrote:

Your retraction is too slow, I'm guessing, because 1mm is more than enough. Try 70mm/s

And you are slightly over extruding.

]]> https://www.soliforum.com/user/2291/ 2015-02-20T01:00:21Z https://www.soliforum.com/post/86279/#p86279 <![CDATA[Re: Slic3r giving me hell AGAIN]]> Your retraction is too slow, I'm guessing, because 1mm is more than enough. Try 70mm/s

]]> https://www.soliforum.com/user/7321/ 2015-02-20T00:50:19Z https://www.soliforum.com/post/86277/#p86277 <![CDATA[Re: Slic3r giving me hell AGAIN]]> That does seem to be the case, Jago. Left is Slic3r, right Cura. Printed solid and fine minus stringy bits. Thanks for info and help

http://s8.postimg.org/57c8rzy0x/image.jpg

]]> https://www.soliforum.com/user/8772/ 2015-02-20T00:44:56Z https://www.soliforum.com/post/86275/#p86275 <![CDATA[Re: Slic3r giving me hell AGAIN]]> The thing is the gap indicates the size of the extrusion lines. It doesn't mean there will be a gap in the actual print. It's awkward but that's how they chose to do it.

]]> https://www.soliforum.com/user/7321/ 2015-02-20T00:29:25Z https://www.soliforum.com/post/86274/#p86274 <![CDATA[Re: Slic3r giving me hell AGAIN]]> Ok im going to print that faceplate for pillowblock (one thats all gappy) and see if its just preview problem or actually will print that bad

]]> https://www.soliforum.com/user/8772/ 2015-02-20T00:25:42Z https://www.soliforum.com/post/86271/#p86271 <![CDATA[Re: Slic3r giving me hell AGAIN]]> Take the average of all those and then do .48/average. That is your extrusion multiplier.

Edit: oh, just use .49 if only one is off. So it'll be .48/.49 = 0.979 = 0.98

]]> https://www.soliforum.com/user/7321/ 2015-02-20T00:15:59Z https://www.soliforum.com/post/86269/#p86269 <![CDATA[Re: Slic3r giving me hell AGAIN]]> Staring at print from front the measurement is .49, left .49, rear .49 and right .51

]]> https://www.soliforum.com/user/8772/ 2015-02-20T00:08:55Z https://www.soliforum.com/post/86268/#p86268 <![CDATA[Re: Slic3r giving me hell AGAIN]]> hmm.. your settings actually seem fine except your nozzle diameter is off - it is set as 0.42 mm. this is probably messing with the toolpath preview and it showing things just a tad further apart because of it. your machine has a 0.4 mm nozzle, so set that under printer settings -> extruder 1.

so bump up that e steps per mm, calibrate with a cube, set your diameter to 0.4 and try again. should work fine.

]]> https://www.soliforum.com/user/7321/ 2015-02-19T23:46:47Z https://www.soliforum.com/post/86263/#p86263 <![CDATA[Re: Slic3r giving me hell AGAIN]]> you are under-extruding, bump up that e steps per mm to 210 (105 * 2 = 210 for 1/32 microstepping) and re-do the calibration cube test

ill look at your settings in a bit, i had a hard drive crash so im reinstalling everything as we speak

]]> https://www.soliforum.com/user/7321/ 2015-02-19T23:34:35Z https://www.soliforum.com/post/86255/#p86255 <![CDATA[Re: Slic3r giving me hell AGAIN]]> http://i57.tinypic.com/2w3ubee.png

not sure why x says zero its 160

]]> https://www.soliforum.com/user/8772/ 2015-02-19T23:28:45Z https://www.soliforum.com/post/86252/#p86252 <![CDATA[Re: Slic3r giving me hell AGAIN]]> Infill is 100%...let me get other info jag. It does it with every STL Jago

]]> https://www.soliforum.com/user/8772/ 2015-02-19T23:19:21Z https://www.soliforum.com/post/86251/#p86251 <![CDATA[Re: Slic3r giving me hell AGAIN]]> Post your eeprom settings dialog, and slic3r ini again. Attach the ini, don't paste. Also the stl you're trying to print if you don't mind

]]> https://www.soliforum.com/user/7321/ 2015-02-19T22:25:26Z https://www.soliforum.com/post/86243/#p86243