<![CDATA[SoliForum - 3D Printing Community — Hacks & Mods]]> 2024-09-03T04:23:02Z PunBB https://www.soliforum.com/ <![CDATA[It's 2024 and my SD4 is still printing]]> I am late to the party and only started modding my SD4 since 2018.
Recent notable mods were definitely the new Mic-6 plate + Keenovo 24v 250W heater.
Definitely made the long wait for the bed to heat up a thing of the past! reach 90C in 5 mins.

]]> https://www.soliforum.com/user/7044/ 2024-09-03T04:23:02Z https://www.soliforum.com/topic/19421/its-2024-and-my-sd4-is-still-printing/new/posts/ <![CDATA[Re-use for Solidoodle Printer]]> What alternative uses have Solidoodle owners put their machines too?
I used mine up until 2019 for printing and then moved on to Sunlu S8's. The perspex parts in the extruder cracked to the point where it kept blocking so it was time to retire it from printing.
But what else could I use the XYZ system for as that still worked perfectly. In my case I magnetically attached a USB microscope to the head and used the Z axis for fine focus (0.1mm steps) and the X&Y axis to move the microscope and take pictures which could then be stitched together like a Panoramic image. I've also used it to take a number of images changing the focus through a subject and then stacking the images to get a deeper focus picture.
Since then I've removed the extruder head and stepper and printed a bracket to attach the Microscope.
This image of a Blue Bottle Fly head is the result of stacking together 10 images to increase the depth of field (focus).
http://soliforum.com/i/?Rpyw2nu.jpg

]]> https://www.soliforum.com/user/19923/ 2021-10-03T07:57:25Z https://www.soliforum.com/topic/18936/reuse-for-solidoodle-printer/new/posts/ <![CDATA[Solidoodle 2 Titan/Aero conversion]]> A blast from the past: My (heavily modified) ancient solidoodle 2 has just been converted to use a Titan Aero extruder/hotend combo.

The parts on thingiverse: https://www.thingiverse.com/thing:4941291

Summary info: https://tomhorsley.com/hardware/solidoo … -aero.html

Extended saga of the conversion process: https://tomhorsley.com/hardware/corexy/ … -aero.html

I used a corexy printer I built using printed parts from the solidoodle to make the printed parts for this conversion :-).

First fairly decent print:

https://tomhorsley.com/hardware/corexy/gallery/aero-good-print.jpg

]]> https://www.soliforum.com/user/270/ 2021-08-25T18:31:55Z https://www.soliforum.com/topic/18923/solidoodle-2-titanaero-conversion/new/posts/ <![CDATA[solidlab in process]]> hello
i will remake this printer like corexy , i see many inforrmation , i will show the progress of the built of this printer
need a real cad design like step file .
thank you
http://www.soliforum.com/misc.php?action=pun_attachment&amp;item=11465&amp;download=1

]]> https://www.soliforum.com/user/18021/ 2021-04-01T11:24:40Z https://www.soliforum.com/topic/18855/solidlab-in-process/new/posts/ <![CDATA[Help with putting e3d v6 in solidoodle 4]]> Hey guys. I'm trying to put my e3d v6 in my solidoodle 4. I'm having trouble figuring out what to do with the wiring. The fan and thermistor are normal little connectors, but the heat thing is just these 2 thick wires with these weird thick pins. I have no clue how to connect these or what I need to buy. I could technically solder them to the little red plug for my stock wiring./ But idk what the norm to do is, the little wiki guides I found didnt really touch on this stuff. On the board theres this 4 pin connector that goes to the red and blue stock plugs, so the easiest option would be to solder to those. But idk if thats what I should do or not. And I dont know where to plug the fan in so that it will properly cool the v6. I havent tried any firmware stuff but I did see the thread on that so I shouldnt need help with that yet. I just wanted to get everything plugged in first. Thanks for any help.

]]> https://www.soliforum.com/user/6894/ 2020-12-30T05:06:15Z https://www.soliforum.com/topic/18801/help-with-putting-e3d-v6-in-solidoodle-4/new/posts/ <![CDATA[sos urgente]]> good afternoon I would like to know 2 things a manual that specifies all the parts of solidoodle bombre of them to look for spare parts. and the second someone can help me I have tried to add support to the models but it does not accept changes. how to make a help with a manual or step-by-step video for this option to print with solidoodle. and if someone has used cure what would be the parameters to recognize the printer thanks

]]> https://www.soliforum.com/user/24379/ 2020-05-13T03:47:53Z https://www.soliforum.com/topic/18591/sos-urgente/new/posts/ <![CDATA[Pancake Extruder Stepper?]]> Hey friends!

I'm looking to do some updates to my SD3. After years of printing with only ABS and having issues, then years of letting the printer sit I'm back to printing smile Switching to PLA and PETG has been super rewarding!

Upgrade list:
Re-printed Lawsy carriages
Replace rods and barrings
buildtak flex plate bed
M5 z-rod replacement
part cooler fan

Questions:
1. Is the case fan on the SD3 required? I bought a replacement, but if I can eliminate a fan I wouldn't mind.
2. Has anyone tried a pancake Nema17 for the extruder motor? I'm wondering if I can gain some accuracy by reducing the carriage weight. The pancake nemas weigh about 200g less than the standard ones. The specs seem very similar.
3. What are your thoughts on upgrading the PCB? I'm interested in upgrading that as well if it will lead to better prints, but the reviews seem mixed on if that will help or not.

Thanks as always for the support

]]> https://www.soliforum.com/user/11735/ 2020-04-16T15:36:10Z https://www.soliforum.com/topic/18536/pancake-extruder-stepper/new/posts/ <![CDATA[Help, extruder is not running]]> Hello everyone,

I used to run TH3D 1.9 Unified Firmware on my Ender 3 as I was using an ABL. I recently got a Titan Aero Extruder and tried to install it. I bought a random 24v Nema 17 Stepper motor online and connected it. I then flashed my firmware to unified firmware 2.1d, enabled Ender3, my mount, the titan aero extruder settings as well as the hotend settings in the firmware and flashed it again.

Heating up the hotend and calibrating the ABL was no problem. But when I went to -> prepare -> move axis -> extruder and tried to move it.. but nothing happens. I tried 3 different cables and 3 different stepping motors (including the original ender 3 stock cable and stock motor) but it isnt moving. I flashed back to 1.9 Firmware, the one I had before, disabling all the titan aero settings and still nothing is moving.

I tried to take someones advise and turned the stepping motor as fast as I could manually; it didnt light the display up but it made the part cooling fan move. The board at least doesnt look damage and doesnt smell burned.

What could it be? I am not too tech savvy and am learning by doing, so please take it slow

]]> https://www.soliforum.com/user/23681/ 2020-03-20T04:39:19Z https://www.soliforum.com/topic/18482/help-extruder-is-not-running/new/posts/ <![CDATA[Replacement Solidoodle bed and upgraded leadscrew]]> My most reliable SD2 has been down for repairs for about 5 months. While working around an INSANE work schedule, I've repleaced two Z motors and two 3/8" leadscrews and I still have Z binding. This printer dubbed the Spookidoodle has been an absolute workhorse for me, and I thought it deserved a second chance at life. So, I decided to make a completely new bed sled from scratch using 2020 extrusions, printed parts, and some upgrades like a 8mm leadscrew that glides smoother than glass, and a new motor just for kicks. This is something I've been wanting to do for a few years, but never had the time or energy in the same moment. This is a prototype ready to install after printing the last two parts. From my measurements, it should work for SD3 aside from the length. I should be ready to install and test by the end of the week. Let me know if anyone is interested in specs or updates.
replacement SD2 bed

]]> https://www.soliforum.com/user/4188/ 2020-02-04T00:13:05Z https://www.soliforum.com/topic/18415/replacement-solidoodle-bed-and-upgraded-leadscrew/new/posts/ <![CDATA[Solidoodle Workbench Overhaul x2]]> The time has come to squeeze more out of what my Solidoodle Workbench can offer.

I'll be using this post over the next month or so to document and discuss upgrade paths for the SD WB.

My goals:

Upgrade print tolerances as much as possible. My prints can sometimes be off over 1mm in the Y direction and of course the Z banding issue is present. The amount of weight on the Y axis causes some wicked ghosting. I want that gone. I want less noise as well. I'd also appreciate faster warm up times, and the ability to go hotter for more material capability. Maybe 24 volt upgrade is in order?


Board - Duet 2 WiFi likely my go-to. I hear it can reduce noise as well, and I want that.

Z-Axis threaded rod - I'm ordering some M5-0.8 threaded rod to replace what's currently there. I'll be using a 5mm to 5mm clamp style coupler and a few M5-0.8 nuts with a printed attachment bracket.

Extruder/Hotend - I'm looking at going the E3D route with a Titan Aqua. One of my extruder steppers failed which sparked this whole upgrade project. Not to mention I'm constantly getting blockages which are causing my prints to fail. This will be purchased last.


Pending Purchases:

Z-Axis stuff from Amazon:
-Fevas Flexible Clamping Coupler:5mm to 5mm,1pcs/lot.
-Steel Hex Nut, Zinc Plated Finish, Class 6, DIN 934, Metric, M5-0.8 Thread Size, 8 mm Width Across Flats, 4 mm Thick (Pack of 100)
-18-8 Stainless Steel Fully Threaded Rod, Meets DIN 975, M5-0.8 Thread Size, 1 m Length, Right Hand Threads

Duet 2 Wifi- I'm not going the thermocouple route with the Titan Aqua (at least not yet) but I believe I still need the PT100 board add-on, can someone confirm this for me?

E3D Titan Aqua- This will be purchased at a later time as the Duet 2 Wifi hogs my budget.


I'd like to think about 24v power supplies but honestly that's a bit outside my area of expertise.


Regards,
Esochi

]]> https://www.soliforum.com/user/21886/ 2019-09-24T17:07:53Z https://www.soliforum.com/topic/18228/solidoodle-workbench-overhaul-x2/new/posts/ <![CDATA[Add A Filament Runout Sensor?]]> Hey everyone,

I am just curious if anyone has added a filament runout sensor to a Solidoode 2?

Had my first filament runout fail while I was away from the printer for a while and it just got me thinking about it.

There are loads of options for them on Amazon like this one: https://www.amazon.com/XCSOURCE-Printer … amp;sr=8-8

I suspect the board on my SD2 does not have a free location to plug it in though. And I am sure there will be an update to firmware required.

Has anyone done this mod?

]]> https://www.soliforum.com/user/457/ 2019-06-27T20:21:54Z https://www.soliforum.com/topic/18125/add-a-filament-runout-sensor/new/posts/ <![CDATA[Hobgoblin]]> Just got s Hobgoblin.  My original hobbed gear is about wore out, quits extruding mid print, no clogs just doesn't push the filament thru.  Having trouble with the bearing that compresses the filament against the goblin.  Someone said Ward Jr made a different printed piece - this is a while ago.  Can someone steer me to that, or is there another mod that will work? 

TIA
Ski

]]> https://www.soliforum.com/user/3790/ 2019-05-26T17:17:18Z https://www.soliforum.com/topic/18086/hobgoblin/new/posts/ <![CDATA[SuperDoodle - Design Progress]]> http://soliforum.com/i/?IF6PMzb.jpg

I hate putting stuff up before it's finished but I figured there might be some helpful criticism out there. I have been pinging ideas off the guys in chat but they are going to be well sick of me before this project gets done.

Here is the Fusion 360 Project Link

The goal for this build:

  • Use the SD3 frame to construct a high performance printer

  • Create the largest build volume possible inside of the SD3 frame (currently looking like 250x250x300

  • Try to keep parts around $800 - $1000

  • All parts should be off the shelf commercially available (some modification to parts okay)

  • Make sure that the build will be future proofed

  • In the spirit of the Solidoodle, make it easily moddable

  • Include the following features:

    • Capable of printing to temps of 400C

    • Bed capable of 150C

    • Auto bed leveling (or mesh bed leveling)

    • Multi-extruder capable

    • 200 mm + print speeds

    • .25mm layer heights

    • Hotends should be quick swappable (think ultimaker)


My progress to date: (2019-03-03)

  • Reverse-engineered SD3 sheet metal frame and cutouts

  • Basic layout of Z Axis and feet

  • Most motion parts selected

  • Bed mounts created

  • Feet finished

  • Core XY motor mounts created

  • Added first revision of tensioner pulleys

To Do: (r/restofthefuckingowl)

  • Mount MGN12 rail for Z -Axis (need to decide on size first, see issues below)*

  • Add mounting points for future HDPE Side, front and bottom panels

  • Create mounts for bowden steppers

  • Make XY carriage assembly

  • Make mount for hotend(s), probe and fans

  • Design hotend interface PCB(maybe Rev.2)

  • Make final BOM and source parts

I have a couple issues that I am looking to solve.
First, the bed I want to use is really close on space so I had to remove a small piece of the mount in the rear. I think that is going to translate into my having to get the grinder out to finish it.

Second, along those same lines, is the mgn12 z axis rails. They are 330 mm long but I can't find those. The max length that will fit is 347mm for the SD3. The closest I found is 350 mm. I have access to a mill so that might not be impossible to shave 3-4 mm off. Might use the grinder again?

Lastly, for now, tolerances are too tight everywhere. Need to generally relax the tolerances to make up for the metric and imperial conversions that they used on the frame. Seems like everything is off just enough that everything is just past snug

Update: 2019/02/24

I think that I managed a decent pair of motor mounts without drilling more holes. Test fitting may change my thoughts on that. Here are some screen grabs. I updated the link to the latest version for anyone that wants to download the files.

http://soliforum.com/i/?JUVADsv.png
http://soliforum.com/i/?OAV77Ls.png

Update: 2019/03/03

Slow progress this weekend. Added a set of from pulley tensioners. Ends up being a 3 part system. Not really happy with the solution but it's a starting point. Current issue is the XY carriages. I am having trouble figuring out how to affix the mgn rail. I think this might have to go to 10 mm rod instead.

Per usual, I have updated the fusion 360 link and added a couple progress pics below.

http://soliforum.com/i/?8KoLPgE.png
http://soliforum.com/i/?s8SjzBC.png

]]> https://www.soliforum.com/user/1906/ 2019-02-23T01:53:35Z https://www.soliforum.com/topic/17958/superdoodle-design-progress/new/posts/ <![CDATA[Rumba vs Ramps? Help with rebuild...]]> Alright, as some of you know Ive been working on this "SD3" for some time now. It has made more test prints then successful ones. I've seen results a lot of you are getting after upgrading. i have installed a handful of them, yet with little success. I want to keep going and get this printer turning out higher quality prints. I have been hit with issue after issue. I now want to upgrade away from the Sang 1.3a i have now. I cant get firmware to upload now...again.

Suggestions on board options please. pros & cons of rumba vs ramps? I am looking for a board that is user friendly, robust, less head-spins, more of a plug and play & tune kind of deal. I've seen some of the kits on amazon that come with an LCD & drivers.

]]> https://www.soliforum.com/user/7496/ 2018-12-31T03:49:22Z https://www.soliforum.com/topic/17824/rumba-vs-ramps-help-with-rebuild/new/posts/ <![CDATA[Need Help Changing Solidoodle 4 board]]> Solidoodle SD-3DP-4 3D 4th Generation Printer (http://salestores.com/solidoodlesd04.ht … y8dOoonbIU) - this is the model that I have currently. I got it for free because the original owner always had trouble getting it to work.

I have trouble getting it to work too and I want to change the board and use Ramps 1.4

However, I need help from someone who can give me or help me to find a step by step process to change the board and get the printer working.

Thank you.

]]> https://www.soliforum.com/user/19283/ 2018-06-24T04:34:18Z https://www.soliforum.com/topic/17425/need-help-changing-solidoodle-4-board/new/posts/