1 Topic by heartless (edited by heartless 2017-01-08 04:33:03)

  • heartless
  • heartless
  • Member
  • Offline
  • From: Northcentral Wisconsin
  • Registered: 2015-04-08
  • Posts: 2,152

Topic: Solved - motor only turns 90 degrees when I ask for 360?

so got my enclosure kit today, got it all assembled, everything turns on and connects. Yay!

lasers turn on and off fine, camera is working, but when I try to test the turntable rotation by clicking on the rotate button with 360 entered in the box, it only turns 90 degrees - not sure why this is?

here are the settings it came with regarding the motor - i have not changed anything in here, as I have no idea... this is a whole new ballgame for me.. tongue

http://soliforum.com/i/?qDO7fCV.jpg

any guidance here?

SD4 #1 & #2 - Lawsy carriages, E3D v6, Rumba controller board, mirror bed plate, X motor fan, upgraded PSU & Mica bed heater
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1

2 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,623

Re: Solved - motor only turns 90 degrees when I ask for 360?

My best advice is go to bed and hopefully it'll just fix itself???? Maybe?
One can hope wink

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

3 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,623

Re: Solved - motor only turns 90 degrees when I ask for 360?

Couldn't you just change steps per revolution to 3200?

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website

4 Reply by heartless

  • heartless
  • heartless
  • Member
  • Offline
  • From: Northcentral Wisconsin
  • Registered: 2015-04-08
  • Posts: 2,152

Re: Solved - motor only turns 90 degrees when I ask for 360?

wardjr wrote:

My best advice is go to bed and hopefully it'll just fix itself???? Maybe?
One can hope wink


ROFL - that is an idea, but not sure how helpful it really is. tongue

I can try changing the steps and see what happens.

SD4 #1 & #2 - Lawsy carriages, E3D v6, Rumba controller board, mirror bed plate, X motor fan, upgraded PSU & Mica bed heater
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1

5 Reply by heartless

  • heartless
  • heartless
  • Member
  • Offline
  • From: Northcentral Wisconsin
  • Registered: 2015-04-08
  • Posts: 2,152

Re: Solved - motor only turns 90 degrees when I ask for 360?

huh, will you look at that... changing the steps did the trick!

Thanks wardjr!
as always, my hero! lol

SD4 #1 & #2 - Lawsy carriages, E3D v6, Rumba controller board, mirror bed plate, X motor fan, upgraded PSU & Mica bed heater
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1

6 Reply by wardjr

  • wardjr
  • wardjr
  • Moderator
  • Offline
  • From: Minnesota
  • Registered: 2013-06-10
  • Posts: 5,623

Re: Solved - motor only turns 90 degrees when I ask for 360?

Happy Scanning smile

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

wardjr's Website