101

Re: Printable Turntable Laser Scanner

n2ri wrote:

also the maker bot digitizer is at least $1,000 last i checked. so add the cost of yours to the figure in your kickstarter page ;^)

$799, check their site.

102

Re: Printable Turntable Laser Scanner

since I last checked? also it wont run on winXP

Solidoodle 2 with Deluxe kit cover & glass bed with heater. and 2nd board SD2 used not 3rd and alum platform not installed yet still wood. also need cooling fan installed to board. use Repetier Host couple vers. Slic3r also have all free ware STL programs

103

Re: Printable Turntable Laser Scanner

hairu526,
will you be selling these after the Kickstarter?  I would like one, but I dont have the time or money right now.

SD2 - Glass Bed, Fans on PCB and Y motor, Custom enclosure
Slicer - Simplify3D

104

Re: Printable Turntable Laser Scanner

wire10ga wrote:

hairu526,
will you be selling these after the Kickstarter?  I would like one, but I dont have the time or money right now.

It's too early to say.  Right now I'm 100% focused on making the Kickstarter a success.  However, I do plan on offering spare parts for sell.

105

Re: Printable Turntable Laser Scanner

Hi hairu526

I already tryed your software on github and did what you discribed there. Everthing worked till I tryed to start with

root@raspberrypi:/home/pi/freelss/src# sudo ./freelss
./freelss: error while loading shared libraries: libraspicam.so.0.1: cannot open shared object file: No such file or directory
root@raspberrypi:/home/pi/freelss/src#

Then I always get this do you know what I do wrong?

Regards
Patrick

106 (edited by hairu526 2015-01-18 14:24:44)

Re: Printable Turntable Laser Scanner

koegelp wrote:

Hi hairu526
I already tryed your software on github and did what you discribed there. Everthing worked till I tryed to start with
root@raspberrypi:/home/pi/freelss/src# sudo ./freelss
./freelss: error while loading shared libraries: libraspicam.so.0.1: cannot open shared object file: No such file or directory
root@raspberrypi:/home/pi/freelss/src#
Then I always get this do you know what I do wrong?
Regards
Patrick

Patrick, if you are able to build the library but are not able to link against it at runtime then it suggests that the library is not in ld's load path.  The libraries should have installed to /usr/local/lib.

First execute the following:
sudo ldconfig

If you still get the error, open /etc/ld.so.conf.d/libc.conf and verify that /usr/local/lib is in that file.  On my machine it looks like this...

# libc default configuration
/usr/local/lib

Run ldconfig and you should be OK!
sudo ldconfig

Btw, you shouldn't need to do this on Raspbian.  What distribution are you running?

107

Re: Printable Turntable Laser Scanner

Thanks your first tip was it now it works. BEST REGARDS

108

Re: Printable Turntable Laser Scanner

Somehow I missed this on the forums!  I just found out about it yesterday from n2ri at a 3Ders meeting we had in St. Louis.

Now, I'm a backer for a complete kit!

I've been test-driving a friend's Matter and Form scanner for a couple of weeks.  I've enjoyed learning the abilities and limitations of 3D scanning.  I'm glad to support this Kickstarter project, and am looking forward to hearing of everyone's experience with it.

109

Re: Printable Turntable Laser Scanner

Wish I saw this earlier so I don't have to wait as long now...hehe  Just pledged as well.  This is something i've been hoping for awhile now.

SD3, Lawsy Carriages with GT2 belts on x axis, BLTouch, Bondtech BMG extruder, E3D v6 via bowden, MIC6 bed with 200W heater w/SSR relay and a RUMBA controller

110

Re: Printable Turntable Laser Scanner

Hi hairu526

Can you make a drawing about dimensions of the scanner like height, how fat is the distance between the lasers and to the turntable and So on. Would help when rebuilding.

Thanks

Regards
Patrick

111

Re: Printable Turntable Laser Scanner

koegelp wrote:

Hi hairu526
Can you make a drawing about dimensions of the scanner like height, how fat is the distance between the lasers and to the turntable and So on. Would help when rebuilding.
Thanks
Regards
Patrick

You don't have to stick exactly to the dimensions of ATLAS 3D, the software allows you to configure that portion of it.  Although it's not a dimensional drawing, you can see the default locations (in millimeters) of the turn table, camera, and lasers here...  https://github.com/hairu/freelss/blob/m … s.cpp#L270

The center of the turntable is the origin, ie: x=0, y=0, and z=0.

112

Re: Printable Turntable Laser Scanner

How small of an object do you think can be scanned?  e.g. toy soldier, matchbox car, gummi bear, bug collection...just some thoughts.

113

Re: Printable Turntable Laser Scanner

knowack wrote:

How small of an object do you think can be scanned?  e.g. toy soldier, matchbox car, gummi bear, bug collection...just some thoughts.

The smallest object I've scanned is one of those little pink erasers that go on the bottom of pencils.

Like one of these: http://ep.yimg.com/ay/yhst-134059276344 … -144-9.gif

114

Re: Printable Turntable Laser Scanner

can we get the stl files for scanner to start printing the parts?

Solidoodle 2 with Deluxe kit cover & glass bed with heater. and 2nd board SD2 used not 3rd and alum platform not installed yet still wood. also need cooling fan installed to board. use Repetier Host couple vers. Slic3r also have all free ware STL programs

115 (edited by rjp350z 2015-02-05 21:42:07)

Re: Printable Turntable Laser Scanner

N2RI - The STL's are posted on the kickstarter page under updates.

Sorry Link might help.....

https://www.kickstarter.com/projects/15 … urse/posts

116

Re: Printable Turntable Laser Scanner

203k...wow

SD2 with E3D, SD Press, Form 1+
Filastruder
NYLON (taulman): http://www.soliforum.com/topic/466/nylon/

117

Re: Printable Turntable Laser Scanner

so can I still get one of the $209 kits after tomarrow? I wont get my tax refund for likely another week to buy it. I want one but kickstarter reads like offer ends in 25hrs. there are still several left though.

Solidoodle 2 with Deluxe kit cover & glass bed with heater. and 2nd board SD2 used not 3rd and alum platform not installed yet still wood. also need cooling fan installed to board. use Repetier Host couple vers. Slic3r also have all free ware STL programs

118 (edited by cor5151 2015-02-10 06:19:39)

Re: Printable Turntable Laser Scanner

Gratz on the ks campaign! I just seen/missed it but will def be following and building it. I've the parts and pi's already. Gonna start printing it soon

Mad props on this I haven't checked up on it in a while, ever test the blue laser? Think 405nm would work?

So excited to get back and start this project.

would also be interested in purchasing the kit since i missed it. will you be adding pre-orders after ks orders are done? or with batch 3?

119

Re: Printable Turntable Laser Scanner

cor5151 wrote:

would also be interested in purchasing the kit since i missed it. will you be adding pre-orders after ks orders are done? or with batch 3?

Right after the Kickstarter kits are delivered we will be selling the kits online. PM me your email address and I will make sure you are among the first to know when they are available.

120

Re: Printable Turntable Laser Scanner

Excellent job!  I've been following you on KS and here.  I'm looking forward to my scanner, and I hope this works out great for you!