26 Reply by oklok

  • oklok
  • oklok
  • Member
  • Offline
  • From: Sweden
  • Registered: 2014-06-15
  • Posts: 44

Re: Taulman releases 6 new materials

Sure Taulman have many similar products, but honestly many of their filaments are quite expensive count per kg,  and the quality is not yet as far as I know proven to be better than others in the same price range. But they are good at getting new material, that is a good job done.

www.3dfilamenta.com - Affordable filament

oklok's Website

27 Reply by AZERATE

  • AZERATE
  • AZERATE
  • PRINTiT
  • Offline
  • From: Chicago
  • Registered: 2013-11-28
  • Posts: 2,077

Re: Taulman releases 6 new materials

Only 30% funded with 9 days left. Anyone know if this is still happening or has it gone the way of the dodo?

Printit Mason and Printit Horizon printers
Multiple SD2s- Bulldog XL, E3D v5/v6/Lite6, Volcano, Hobb Goblin, Titan, .9 motor, Lawsy carriages, direct Y drive, fishing line...the list goes on
Filawinder and Filastruder #1870.....worth every penny!

28 Reply by DePartedPrinter

  • DePartedPrinter
  • Moderator
  • Offline
  • From: Colorado
  • Registered: 2012-08-14
  • Posts: 1,478

Re: Taulman releases 6 new materials

I'm sure Taulman will make an announcement when the kickstarter is over how they will be moving forward.

SD2 with E3D, SD Press, Form 1+
Filastruder
NYLON (taulman): http://www.soliforum.com/topic/466/nylon/

29 Reply by Stevos758

  • Stevos758
  • Member
  • Offline
  • Registered: 2013-04-22
  • Posts: 502

Re: Taulman releases 6 new materials

Must resist! I was going to sell my printer.... Now not sure..... What happened to the 910 or whatever it was called? I think I still have an experimental roll 1/4 left. Very impressive stuff.

Website - http://rippsgaragetech.com/
Facebook - https://www.facebook.com/pages/Ripps-Ga … 3131469591
E3D V6 Bulldog XL mounts! http://www.filastruder.com/products/e3dv6-bulldog-mount

30 Reply by grob

  • grob
  • grob
  • Member
  • Offline
  • From: Sydney, Australia
  • Registered: 2014-01-02
  • Posts: 900

Re: Taulman releases 6 new materials

DePartedPrinter wrote:

I'm sure Taulman will make an announcement when the kickstarter is over how they will be moving forward.

Survey for KS backers to enter preferences out of the 6 materials just came out - looks to me (putting two and two together and getting five of course) like they're considering limiting the scope to a less audacious variety of materials!

SD3. Mk2b + glass, heated enclosure, GT2 belts, direct drive y shaft, linear bearings, bowden-feed E3D v5 w/ 0.9° stepper
Smoothieboard via Octoprint on RPi

31 Reply by AZERATE

  • AZERATE
  • AZERATE
  • PRINTiT
  • Offline
  • From: Chicago
  • Registered: 2013-11-28
  • Posts: 2,077

Re: Taulman releases 6 new materials

Project was not funded. sad
But due to the survey results, it seems promising they will release Tritan and PCTPE in the near future with hopes of the other materials.

Printit Mason and Printit Horizon printers
Multiple SD2s- Bulldog XL, E3D v5/v6/Lite6, Volcano, Hobb Goblin, Titan, .9 motor, Lawsy carriages, direct Y drive, fishing line...the list goes on
Filawinder and Filastruder #1870.....worth every penny!

32 Reply by grob

  • grob
  • grob
  • Member
  • Offline
  • From: Sydney, Australia
  • Registered: 2014-01-02
  • Posts: 900

Re: Taulman releases 6 new materials

http://taulman3d.com/rewards.html
They've also offered to provide backers with a 'reward' of some kind (I'd suspect perhaps a small discount on the price of a couple of spools) regardless of the kickstarter result.

SD3. Mk2b + glass, heated enclosure, GT2 belts, direct drive y shaft, linear bearings, bowden-feed E3D v5 w/ 0.9° stepper
Smoothieboard via Octoprint on RPi