1

Topic: Hope everyone had a happy new year mine started out bad

about 3;30 am we had an f2 tornado hit causing this.
http://soliforum.com/i/?T4fZEQP.jpg

Makerbot Replicator 2X (Dual ext ruder). Build volume: 9.7" X 6.0" X 6.1"
Printing on Kapton. Over 200 hours on 1 sheet of kapton

2

Re: Hope everyone had a happy new year mine started out bad

Hope all works out.

Soliddoodle 4 stock w glass bed
Folger Tech Prusa 2020 upgraded to  ED3v6 and titan extruder
Marlin/Repetier Host/ Slic3r and Cura

3

Re: Hope everyone had a happy new year mine started out bad

That sucks, break out the chainsaw.

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

4

Re: Hope everyone had a happy new year mine started out bad

Wow!  Hope you got 'Hurricane' coverage as opposed to 'Wind' coverage.  Fine line, but a tornado is not a hurricane....
Good Luck

SD2, E3D V6 & Lite6, Modified MK5 extruder, Lawsy's carriages, 360W P/S, aftermarket heated glass bed - SSR controlled (build table heats to 97C in 3 min), removable Plexiglas enclosure, ball bearings, 6 cooling fans.

5

Re: Hope everyone had a happy new year mine started out bad

I broke the chainsaw working on  debris.
roof leaked and my printer got wet.

Makerbot Replicator 2X (Dual ext ruder). Build volume: 9.7" X 6.0" X 6.1"
Printing on Kapton. Over 200 hours on 1 sheet of kapton

6

Re: Hope everyone had a happy new year mine started out bad

If I were in your neighborhood I'd stop by and help with cleanup.  Anything would be better than shoveling snow again wink

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

7 (edited by dubbsd 2017-01-02 20:44:11)

Re: Hope everyone had a happy new year mine started out bad

wardjr
I have shoveled snow and it is no fun. grew up in Remer Minn.
been living in north west FL the last 45 years. I would rather shovel snow than go through another tornado or cat 4 hurricane.
and as i type this we are under another tornado warning.

Makerbot Replicator 2X (Dual ext ruder). Build volume: 9.7" X 6.0" X 6.1"
Printing on Kapton. Over 200 hours on 1 sheet of kapton

8

Re: Hope everyone had a happy new year mine started out bad

Remer is only 20 minutes away from me.  Home of Big Foot wink
If you ever come up for a visit, look me up!!!!

Crazy how small the world is.

Be safe!!!

Printit Industries Model 8.10 fully enclosed CoreXY, Chamber heat
3-SD3's & a Workbench all fully enclosed, RH-Slic3r Win7pro, E3D V6, Volcano & Cyclops Hot End
SSR/500W AC Heated Glass Bed, Linear bearings on SS rods. Direct Drive Y-axis, BulldogXL
Thanks to all for your contributions

9

Re: Hope everyone had a happy new year mine started out bad

I live in joisey . The poorest county in the state  . High humility , Snow , hurricanes and occasional tornado . forest fires  about the only this we do not get much of is earthquakes  but even one of them once in a while.   
Stay safe

Soliddoodle 4 stock w glass bed
Folger Tech Prusa 2020 upgraded to  ED3v6 and titan extruder
Marlin/Repetier Host/ Slic3r and Cura

10

Re: Hope everyone had a happy new year mine started out bad

I'm glad everyone is ok. Hope the new warning blows over.

I lived in Jacksonville for about 8 years (in Florida for 15 years on and off). In 2008 tropical storm Fay uprooted a tree on our property which fell on our house, piercing the roof and almost killed my wife and I. The insurance company screwed us, the house was abandoned, and we had to start all over after blowing through our life savings to fight homelessness. Days like that are one of many reasons I don't miss Florida, but it always could be worse.

Keep us in the loop so we know you are alright!

Printit 8.10 printer
Multiple SD2s- Bulldog XL, E3D v5/v6/Lite6, Volcano, Hobb Goblin, Titan, .9 motor, Lawsy carriages, direct Y drive, fishing line...the list goes on
Filawinder and Filastruder #1870.....worth every penny!