You are not logged in. Please login or register.
SoliForum - 3D Printing Community → XYZ Printing Hacks & Mods → Repetier problems on 1.0a
I just slapped Repetier on my Da Vinci 1.0a 3F10A (somehow) and it works nicely. I've already gotten all the axes and the extruder to work, as well as playing Imperial March, but my prints keep sticking to the extruder. No matter what I try (sheet of paper calibration, slow speeds on the first layer), nothing works. Any help is appreciated.
I just slapped Repetier on my Da Vinci 1.0a 3F10A (somehow) and it works nicely. I've already gotten all the axes and the extruder to work, as well as playing Imperial March, but my prints keep sticking to the extruder. No matter what I try (sheet of paper calibration, slow speeds on the first layer), nothing works. Any help is appreciated.
So you mean they are not sticking to the bed then? Try a light coat of aquanet hairspray on the bed, or Elmers purple glue stick on the bed..
That seems to have worked. I was so used to not having to use glue with the XYZ firmware that I forgot about it. Printing perfectly now!
I have problem after installing repetier firmware
I experience too much material comes out during print
Any nody has solutions for me?
I have problem after installing repetier firmware
I experience too much material comes out during print
Any nody has solutions for me?
Have you done all your basic calibration? Like extruder steps per mm?
I just slapped Repetier on my Da Vinci 1.0a 3F10A (somehow) and it works nicely. I've already gotten all the axes and the extruder to work, as well as playing Imperial March, but my prints keep sticking to the extruder. No matter what I try (sheet of paper calibration, slow speeds on the first layer), nothing works. Any help is appreciated.
Glad to hear that repetier is working on the new 1.0A model. I also am right on the fence of flashing mine. Was just concerned about reading online that it was not working properly with the 1.0A 3F10A.
Which version did you use? Thanks Dave
I just flashed my xyz da Vinci 1.0 AiO and I'm trying to print PLA
I seem to have got jammed and extruder feed wheels jammed I cleared jam and cleaned wheels but now I can't get wheels to turn again
I love repetier so far much better firmware and first hack too super excited and feeling a bit lost
I just flashed my xyz da Vinci 1.0 AiO and I'm trying to print PLA
I seem to have got jammed and extruder feed wheels jammed I cleared jam and cleaned wheels but now I can't get wheels to turn againI love repetier so far much better firmware and first hack too super excited and feeling a bit lost
Start a new thread, you'll be more likely to get an answer. I can try to help you through PM if you want.
Hello everybody,
Please, please help me:
I have a DA VINCI 1.0 AIO, I tried to make a firmware downgrade from 1.2 to 1.1.3 by bossac, my printer still not working.
How can I solve this isuue.
Thanks in advance.
using bossac with stock FW on AiO / 1.0A/ 2.0A make printer unusable because FW is encrypted for these printers
Contact support or flash repetier
Just installed repetier 0.91 on my davinci 1.0a with win 10 could not install 0.92 Anyway after install can not move z axis up. Have tried setting home position to max, -200 200 inverting the z axis. Seems to me i'm on the limit switch and it is inverted.
Did anyone else have this problem after making the switch. Ya I did not think to home all axis BEFORE SHORTING J37 even reverting to the stock firmware has the same problem.
If I knew which connectors were for the limit switches I would switch them but short of tearing down the whole machine...
Can somebody help.
you have 1.0A this behaviour happen when you use 1.0 FW. 0.91 is not for 1.0A, only 0.92 support it
I see you can revert back to stock FW, it means you use 1.0 FW and not 1.0A FW
It means also you use wrong setting in configuration in repetier
Be sure you set MODEL 1 in repetier (change / save / close / reopen to verify change is done) before flashing
SoliForum - 3D Printing Community → XYZ Printing Hacks & Mods → Repetier problems on 1.0a
Powered by PunBB, supported by Informer Technologies, Inc.
