1 Topic by JGPenland (edited by JGPenland 2015-11-29 12:57:25)

  • JGPenland
  • Member
  • Offline
  • Registered: 2015-03-20
  • Posts: 27

Topic: SD4 with Rumba/E3d V6-Needs repair 450$ obo

Solidoodle 4 with Rumba board, E3d V6 hot end, upgraded power supply.
Stepper motor overheated due to pot being set too high, carriage melted. Will need a new stepper motor.

http://i17.photobucket.com/albums/b64/Penland/88686A91-86AD-4F36-9BB9-449172C1D1C5.jpg

http://i17.photobucket.com/albums/b64/Penland/C82A6A4B-93C4-4ECA-9CC7-B1446037E28A.jpg

http://i17.photobucket.com/albums/b64/Penland/6E7D366F-323F-4943-B3D6-756026E2593C.jpg

http://i17.photobucket.com/albums/b64/Penland/33BF6346-29EE-4F59-B932-7837A6F935C5.jpg

Solidoodle 4-E3D V6- Rumba-Glass Bed-Upgraded PSU

2 Reply by aclark1983

  • aclark1983
  • Member
  • Offline
  • Registered: 2015-12-29
  • Posts: 16

Re: SD4 with Rumba/E3d V6-Needs repair 450$ obo

Sold yet?

3 Reply by heartless

  • heartless
  • heartless
  • Member
  • Offline
  • From: Northcentral Wisconsin
  • Registered: 2015-04-08
  • Posts: 2,152

Re: SD4 with Rumba/E3d V6-Needs repair 450$ obo

also interested. smile

SD4 #1 & #2 - Lawsy carriages, E3D v6, Rumba controller board, mirror bed plate, X motor fan, upgraded PSU & Mica bed heater
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1

4 Reply by Kronikabuse

  • Kronikabuse
  • Kronikabuse
  • Member
  • Offline
  • From: Wi
  • Registered: 2014-08-03
  • Posts: 709

Re: SD4 with Rumba/E3d V6-Needs repair 450$ obo

any news?

Sd4 #9080 with a glass bed. E3d chimera duel extruder. Paste extruder , duet wifi.
Lawsy carriages. linear bearings. Y axis direct drive, Kinect scanner
SD4#8188 glass bed, lawsly carriages, E3d v6, octoprint http://www.ustream.tv/channel/hotrod96z28
Filastruder/filawinder, Custom Delta 300mm x 600mm

5 Reply by heartless

  • heartless
  • heartless
  • Member
  • Offline
  • From: Northcentral Wisconsin
  • Registered: 2015-04-08
  • Posts: 2,152

Re: SD4 with Rumba/E3d V6-Needs repair 450$ obo

I recently sent a forum email to him asking about this one - no response as of yet

SD4 #1 & #2 - Lawsy carriages, E3D v6, Rumba controller board, mirror bed plate, X motor fan, upgraded PSU & Mica bed heater
SD4 #3 - in the works ~ Folgertech FT-5, rev 1
Printit Industries Beta Tester - Horizon H1