181 Possible Firmware Issue
by Codum
- 4 replies
- 1,894 views
- Last post 2015-07-20 03:30:23 by Codum
182 Press Power supply
by userksh14
- 2 replies
- 2,470 views
- Last post 2015-07-17 02:20:06 by trayracing
183 Help! Solidoodle Press Fine tuning?
by xnex8080
- 1 reply
- 999 views
- Last post 2015-07-14 00:33:09 by trayracing
184 Help! MK2B heated bed
by sandcub1971
- 2 replies
- 1,232 views
- Last post 2015-07-12 14:00:42 by Robny
- 18 replies
- 12,261 views
- Last post 2015-07-12 03:37:11 by wardjr
186 jamming/skipping steps/clicking extruder
by ekul3e3
- 8 replies
- 5,357 views
- Last post 2015-07-02 17:33:11 by mrallinwonder
- 26 replies
- 10,341 views
- Last post 2015-07-01 23:32:05 by annalenhartmurray
188 Press Slic3r settings?
by dragonladycels
- 0 replies
- 1,281 views
- Last post 2015-07-01 00:14:51 by dragonladycels
189 Press Thermister
by Robny
- 15 replies
- 6,259 views
- Last post 2015-06-30 18:12:48 by Evmanw
- 1 reply
- 1,259 views
- Last post 2015-06-26 12:25:23 by chenderson
191 Help! Pololu AVR Progammer
by Robny
- 7 replies
- 2,931 views
- Last post 2015-06-26 06:22:38 by Goshdarnit
192 Please Help! Extruder will not heat!
by MLA
- 13 replies
- 4,967 views
- Last post 2015-06-26 01:34:35 by trayracing
193 About press Z limit endstop
by selkess
- 7 replies
- 3,201 views
- Last post 2015-06-25 08:05:35 by selkess
194 Broken Thermister
by aeschneider.tech
- 5 replies
- 2,738 views
- Last post 2015-06-22 02:00:08 by trayracing
195 Help! Prints tend to curl up!
by willthewill
- 21 replies
- 19,792 views
- Last post 2015-06-21 14:28:09 by Crucial
196 extruder problem
by akhs001
- 1 reply
- 939 views
- Last post 2015-06-19 05:04:16 by joeix3
197 Extruder gouging solidoodle filament
by degrassijrhi
- 22 replies
- 10,324 views
- Last post 2015-06-19 04:51:59 by joeix3
198 Help! MK2B Bed/Thermistor Question
by Robny
- 3 replies
- 1,461 views
- Last post 2015-06-15 20:03:32 by Robny
199 Two weeks of adhering/warping issues, could really use some input!
by andersbergstrom85
- 14 replies
- 6,145 views
- Last post 2015-06-14 01:40:09 by seven2099
200 Help! Broken Extruder Stepper?
by Crucial
- 1 reply
- 1,072 views
- Last post 2015-06-14 01:03:07 by Crucial
201 press stepper motor wire swap/replace
by celboy
- 9 replies
- 4,766 views
- Last post 2015-06-10 03:09:42 by celboy
202 Replace Glass Bed with FR4 Perf Board
by Bartimaeus
- 22 replies
- 17,327 views
- Last post 2015-06-09 21:07:33 by TheBaron
203 Help! Build Platform *thumps* and descends mid-print
by H_Alex
- 1 reply
- 1,171 views
- Last post 2015-06-07 14:36:43 by willthewill
- 2 replies
- 1,251 views
- Last post 2015-06-06 08:13:35 by Goshdarnit
205 Offbrand Filament problems for Solidoodle Press
by hkrivell
- 21 replies
- 8,277 views
- Last post 2015-06-06 01:39:03 by hkrivell
206 Press wonkiness
by scruffybob
- 5 replies
- 2,422 views
- Last post 2015-06-04 14:25:25 by scruffybob
207 Solved Cannot Reflash My Firmware No Matter What I Try!
by Goshdarnit
- 9 replies
- 5,236 views
- Last post 2015-06-03 11:28:11 by Goshdarnit
208 Print stopping half way all the time
by juesvic
- 2 replies
- 1,678 views
- Last post 2015-06-01 22:23:37 by juesvic
- 13 replies
- 23,121 views
- Last post 2015-06-01 14:07:59 by mrsnowie
210 Help! IP Address
by flightofdeath
- 0 replies
- 980 views
- Last post 2015-06-01 12:29:45 by flightofdeath