61 Da Vinci 1.0 AIO no connection to pc at all
by markkcunningham
- 7 replies
- 2,699 views
- Last post 2019-11-28 19:05:26 by markkcunningham
62 CR10-S gaps in print/all layers
by markkcunningham
- 3 replies
- 1,244 views
- Last post 2019-11-24 15:47:14 by heartless
- 29 replies
- 8,317 views
- Last post 2019-11-22 11:46:39 by Maurone999
64 question about enclosure (top) for my printer.
by dubbsd
- 4 replies
- 1,358 views
- Last post 2019-11-17 15:43:16 by dubbsd
65 3D printer is not working
by morgan1
- 1 reply
- 879 views
- Last post 2019-11-16 12:45:29 by heartless
66 how are there no lines on these prints?
by johnjack
- 11 replies
- 15,173 views
- Last post 2019-11-13 13:21:07 by carl_m1968
67 CR10-S gaps in print/all layers
by markkcunningham
- 2 replies
- 1,051 views
- Last post 2019-11-13 12:34:01 by carl_m1968
68 Is there a 3D printer that competes with this one? Look for opinions
by BuildItLikeBeckham
- 5 replies
- 1,687 views
- Last post 2019-11-11 22:55:41 by creatorgirl13
69 Need help dialing in my new printer
by dubbsd
- 5 replies
- 3,345 views
- Last post 2019-11-02 22:53:20 by Tin Falcon
70 Prints only print rough on the right side of the printer
by mongozen
- 3 replies
- 1,311 views
- Last post 2019-11-01 09:55:25 by Kronikabuse
71 Ultimaker 2+ freezing at startup
by caskelcey
- 2 replies
- 1,045 views
- Last post 2019-10-24 15:55:41 by caskelcey
72 Printer vibration
by dubbsd
- 1 reply
- 950 views
- Last post 2019-10-19 15:12:46 by heartless
73 Cura extrusion width
by diyengineer
- 1 reply
- 1,636 views
- Last post 2019-10-04 03:00:16 by heartless
74 delta printer kit
by lt72884
- 5 replies
- 1,669 views
- Last post 2019-09-23 11:37:50 by carl_m1968
75 40800 Error on my zcorp Z450.
by okubo777
- 0 replies
- 1,304 views
- Last post 2019-09-02 10:52:36 by okubo777
76 discontinuous first layer prusa slicer
by lt72884
- 1 reply
- 6,456 views
- Last post 2019-08-30 03:15:17 by lt72884
- 2 replies
- 27,640 views
- Last post 2019-08-16 12:17:50 by hidom
- 77 replies
- 33,779 views
- Last post 2019-08-14 01:42:12 by Tin Falcon
79 Nozzle heat fluctuation. Why?
by dubbsd
- 3 replies
- 1,467 views
- Last post 2019-08-04 21:19:38 by carl_m1968
80 Stepper motor in Heating chamber
by Athul
- 0 replies
- 876 views
- Last post 2019-07-29 05:27:03 by Athul
81 Solidoodle 2 spec question
by rcromwell92
- 4 replies
- 1,515 views
- Last post 2019-07-29 03:04:58 by heartless
- 63 replies
- 30,113 views
- Last post 2019-07-25 13:10:55 by makegeneve
83 Any idea why I am getting layer separation
by ennogs
- 4 replies
- 1,417 views
- Last post 2019-07-22 02:07:58 by carl_m1968
84 BAD stepper ???(solved)
by Tin Falcon
- 1 reply
- 1,134 views
- Last post 2019-07-19 01:43:28 by Tin Falcon
85 Newbie desperate for help.....
by davidhk129
- 20 replies
- 4,705 views
- Last post 2019-07-18 15:29:25 by davidhk129
86 thinking of buying an ultamaker 3 any comments
by dubbsd
- 2 replies
- 1,162 views
- Last post 2019-07-15 01:35:30 by Tin Falcon
87 MP Mini V2
by L7NirvanaLove
- 5 replies
- 1,817 views
- Last post 2019-07-12 22:47:22 by L7NirvanaLove
88 Junior 1.0 and error code 00030
by william1944
- 5 replies
- 1,936 views
- Last post 2019-07-02 10:39:55 by william1944
89 Diskrete Klingeltöne
by MartinL
- 0 replies
- 890 views
- Last post 2019-06-27 07:51:58 by MartinL
90 Monoprice Maker Ultimate - bed heater current
by Dave455
- 7 replies
- 2,206 views
- Last post 2019-06-22 03:50:45 by Dave455